Datenblatt-pdf.com


IN25AA160D Schematic ( PDF Datasheet ) - Integral

Teilenummer IN25AA160D
Beschreibung NONVOLATILE ELECTRICALLY ERASABLE PROM
Hersteller Integral
Logo Integral Logo 




Gesamt 10 Seiten
IN25AA160D Datasheet, Funktion
IN25АА080N, IN25АА080D, IN25АА160N, IN25АА160D
NONVOLATILE ELECTRICALLY ERASABLE PROM WITH SERIAL
PERIPHERAL INTERFACE (SPI).
functionally compartible to 25AA080, 25AA160 (Microchip)
DESCRIPTION
The IN25АА080N/D are a 8K(1Kx8) serial Electrically Erasable PROM with SPI interface.
*The IN25АА160N/D are a 16K (2Kx8) serial Electrically Erasable PROM with SPI interface (SPI).
The ICs is purposed for reading, writing & nonvolatile data storage in electronic units with SPI interface. ICs
are realized in SO-8 (MS-012АA) and DIP-8 (MS-001BA)
FEATURES
- Data capacity, QINF:
for IN25АА080N, IN25АА080D
for IN25АА160N, IN25АА160D
8192 bit,
16384 bit;
- Maximum clock frequency, fC:
for 4,5 V UCC 5,5 V
for 2,5 V UCC 5,5 V
for 1,8 V UCC 5,5 V
- Maximum stand-by current, ICC:
for UCC = 5,5 V, UIL = 0 V, UIH = UCC
for UCC = 2,5 V, UIL = 0 V, UIH = UCC
- Maximum read current, IOCCR :
3 MHz;
2 MHz;
1 MHz;
5,0 uA
1,0 uA;
for UCC = 5,5 В, fC = 3,0 МГц, SO pin is not loaded .…1,0 mA,
for UCC = 2,5 В, fC = 2,0 МГц, SO pin is not loaded …..0,5 mA;
- Maximum write current, IOCCW :
for UCC = 5,5 V
5,0 mA;
for UCC = 2,5 V
3,0 mA;
- Byte & page (16 bytes) data write modes are available;
- Endurance NE/W, …...1000000 cycles;
- Build-in write protection block
- Write protection for 1/4, 1/2, or all of storage array;
- Power on/off data protection circuitry;
- Supply voltage UCC 1,8 … 5,5 V;
- Operating temperature range -40 … +85°C.
- 100 years non-volatile data retention time
N SUFFIX
DIP
8
1 D SUFFIX
8 SOIC
1
Pin
Name
CS
SO
WP
GND
SI
SCK
HOLD
VCC
Function
Chip Select
Serial Data Output
Write protection
Ground
Serial Data Input
Clock Input
Hold input *
Power Supply
PIN FUNCTIONS
CS 01
SO 02
WP 03
GND 04
08 Vcc
07 HOLD
06 SCK
05 SI
Ver.00/13.10.2008
IN25AA080(160)-TSe
1 2263040






IN25AA160D Datasheet, Funktion
IN25АА080N, IN25АА080D, IN25АА160N, IN25АА160D
Byte write sequence
Read status register sequence
The RDSR (read status register) instruction provides access to the status register. The status register may
be read at any time, even during a write cycle.
The 0th bit - WIP bit (Write-In-Process) of the status register indicates whether the IC is busy with a write
operation. When set to a ‘1’ a write is in progress, when set to a ‘0’ no write is in progress. This bit is read
only.
The 1st bit - WEL bit (Write Enable Latch) of the status register indicates the status
of the write enable latch. When set to a ‘1’ the latch allows writes to the array, when set to a ‘0’ the latch pro-
hibits writes to the array. This bit is read only.
The 2nd & 3rd bits - BP0 and BP1 bits (Block Protection) indicate which blocks are currently write protected.
These bits are set by the user issuing the WRSR instruction.
The SCK is used to synchronize the communication between a master and the IC. Instructions, addresses,
or data present on the SI pin are latched on the rising edge of the clock input, while data on the SO pin is
updated after the falling edge of the clock input.
Ver.00/13.10.2008
IN25AA080(160)-TSe
6 2263040

6 Page







SeitenGesamt 10 Seiten
PDF Download[ IN25AA160D Schematic.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
IN25AA160DNONVOLATILE ELECTRICALLY ERASABLE PROMIntegral
Integral
IN25AA160NNONVOLATILE ELECTRICALLY ERASABLE PROMIntegral
Integral

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com       |      2020       |      Kontakt     |      Suche