|
|
|
MX29LV320B Schematic ( PDF Datasheet ) - Macronix
| Teilenummer | MX29LV320B |
|
| Beschreibung | 32M-bit Single Voltage 3V Only Flash Memory | |
| Hersteller | Macronix | |
| Logo |  |
|
Gesamt 30 Seiten 
MX29LV320T/B
32M-BIT [4M x 8 / 2M x 16] SINGLE VOLTAGE
3V ONLY FLASH MEMORY
FEATURES
GENERAL FEATURES
• 4,194,304 x 8 / 2,097,152 x 16 switchable
• Sector Structure
- 8K-Byte x 8 and 64K-Byte x 63
• Extra 64K-Byte sector for security
- Features factory locked and identifiable, and cus-
tomer lockable
• Twenty-Four Sector Groups
- Provides sector group protect function to prevent pro-
gram or erase operation in the protected sector group
- Provides chip unprotect function to allow code chang-
ing
- Provides temporary sector group unprotect function
for code changing in previously protected sector groups
• Single Power Supply Operation
- 2.7 to 3.6 volt for read, erase, and program opera-
tions
• Latch-up protected to 250mA from -1V to Vcc + 1V
• Low Vcc write inhibit is equal to or less than 1.4V
• Compatible with JEDEC standard
- Pinout and software compatible to single power sup-
ply Flash
PERFORMANCE
• High Performance
- Fast access time: 70/90/120ns
- Fast program time: 7us/word typical utilizing acceler-
ate function
- Fast erase time: 1.6s/sector, 112s/chip (typical)
• Low Power Consumption
- Low active read current: 10mA (typical) at 5MHz
- Low standby current: 200nA (typical)
• Minimum 100,000 erase/program cycle
• 10-year data retention
SOFTWARE FEATURES
• Erase Suspend/ Erase Resume
- Suspends sector erase operation to read data from
or program data to another sector which is not being
erased
• Status Reply
- Data polling & Toggle bits provide detection of pro-
gram and erase operation completion
• Support Common Flash Interface (CFI)
HARDWARE FEATURES
• Ready/Busy (RY/BY) Output
- Provides a hardware method of detecting program
and erase operation completion
• Hardware Reset (RESET) Input
- Provides a hardware method to reset the internal state
machine to read mode
• WP/ACC input pin
- Provides accelerated program capability
PACKAGE
• 48-Pin TSOP
• 48-Ball CSP
GENERAL DESCRIPTION
The MX29LV320T/B is a 32-mega bit Flash memory or-
ganized as 4M bytes of 8 bits and 2M words of 16 bits.
MXIC's Flash memories offer the most cost-effective and
reliable read/write non-volatile random access memory.
The MX29LV320T/B is packaged in 48-pin TSOP and
48-ball CSP. It is designed to be reprogrammed and
erased in system or in standard EPROM programmers.
The standard MX29LV320T/B offers access time as fast
as 70ns, allowing operation of high-speed microproces-
sors without wait states. To eliminate bus contention,
the MX29LV320T/B has separate chip enable (CE) and
output enable (OE) controls.
MXIC's Flash memories augment EPROM functionality
with in-circuit electrical erasure and programming. The
MX29LV320T/B uses a command register to manage
this functionality.
MXIC Flash technology reliably stores memory
contents even after 100,000 erase and program
cycles. The MXIC cell is designed to optimize the
erase and program mechanisms. In addition, the
combination of advanced tunnel oxide processing
and low internal electric fields for erase and
programming operations produces reliable cycling.
P/N:PM0742
REV. 1.4, JUL. 04, 2003
1
 
MX29LV320T/B
Sector
Group
11
11
11
11
12
12
12
12
13
13
13
13
14
14
14
14
15
15
15
15
16
16
16
17
18
19
20
21
22
23
24
Sector
SA40
SA41
SA42
SA43
SA44
SA45
SA46
SA47
SA48
SA49
SA50
SA51
SA52
SA53
SA54
SA55
SA56
SA57
SA58
SA59
SA60
SA61
SA62
SA63
SA64
SA65
SA66
SA67
SA68
SA69
SA70
Sector Address
A20-A12
101000xxx
101001xxx
101010xxx
101011xxx
101100xxx
101101xxx
101110xxx
101111xxx
110000xxx
110001xxx
110010xxx
110011xxx
110100xxx
110101xxx
110110xxx
110111xxx
111000xxx
111001xxx
111010xxx
111011xxx
111100xxx
111101xxx
111110xxx
111111000
111111001
111111010
111111011
111111100
111111101
111111110
111111111
Sector Size
(Kbytes/Kwords)
64/32
64/32
64/32
64/32
64/32
64/32
64/32
64/32
64/32
64/32
64/32
64/32
64/32
64/32
64/32
64/32
64/32
64/32
64/32
64/32
64/32
64/32
64/32
8/4
8/4
8/4
8/4
8/4
8/4
8/4
8/4
(x8)
Address Range
280000h-28FFFFh
290000h-29FFFFh
2A0000h-2AFFFFh
2B0000h-2BFFFFh
2C0000h-2CFFFFh
2D0000h-2DFFFFh
2E0000h-2EFFFFh
2F0000h-2FFFFFh
300000h-30FFFFh
310000h-31FFFFh
320000h-32FFFFh
330000h-33FFFFh
340000h-34FFFFh
350000h-35FFFFh
360000h-36FFFFh
370000h-37FFFFh
380000h-38FFFFh
390000h-39FFFFh
3A0000h-3AFFFFh
3B0000h-3BFFFFh
3C0000h-3CFFFFh
3D0000h-3DFFFFh
3E0000h-3EFFFFh
3F0000h-3F1FFFh
3F2000h-3F3FFFh
3F4000h-3F5FFFh
3F6000h-3F7FFFh
3F8000h-3F9FFFh
3FA000h-3FBFFFh
3FC000h-3FDFFFh
3FE000h-3FFFFFh
(x16)
Address Range
140000h-147FFFh
148000h-14FFFFh
150000h-157FFFh
158000h-15FFFFh
160000h-147FFFh
168000h-14FFFFh
170000h-177FFFh
178000h-17FFFFh
180000h-187FFFh
188000h-18FFFFh
190000h-197FFFh
198000h-19FFFFh
1A0000h-1A7FFFh
1A8000h-1AFFFFh
1B0000h-1B7FFFh
1B8000h-1BFFFFh
1C0000h-1C7FFFh
1C8000h-1CFFFFh
1D0000h-1D7FFFh
1D8000h-1DFFFFh
1E0000h-1E7FFFh
1E8000h-1EFFFFh
1F0000h-1F7FFFh
1F8000h-1F8FFFh
1F9000h-1F9FFFh
1FA000h-1FAFFFh
1FB000h-1FBFFFh
1FC000h-1FCFFFh
1FD000h-1FDFFFh
1FE000h-1FEFFFh
1FF000h-1FFFFFh
Note:The address range is A20:A-1 in byte mode (BYTE=VIL) or A20:A0 in word mode (BYTE=VIH)
Top Boot Security Sector Addresses
Sector Address
A20~A12
111111xxx
Sector Size
(Kbytes/Kwords)
64/32
(x8)
Address Range
3F0000h-3FFFFFh
(x16)
Address Range
1F8000h-1FFFFFh
P/N:PM0742
REV. 1.4, JUL. 04, 2003
6
6 Page 
MX29LV320T/B
OUTPUT DISABLE
With the OE input at a logic high level (VIH), output from
the devices are disabled. This will cause the output pins
to be in a high impedance state.
RESET OPERATION
The RESET pin provides a hardware method of resetting
the device to reading array data.When the RESET pin is
driven low for at least a period of tRP, the device
immediately terminates any operation in progress,
tristates all output pins, and ignores all read/write
commands for the duration of the RESET pulse. The
device also resets the internal state machine to reading
array data.The operation that was interrupted should be
reinitiated once the device is ready to accept another
command sequence, to ensure data integrity
Current is reduced for the duration of the RESET pulse.
When RESET is held at VSS±0.3V, the device draws
CMOS standby current (ICC4). If RESET is held at VIL
but not within VSS±0.3V, the standby current will be
greater.
The RESET pin may be tied to system reset circuitry. A
system reset would that also reset the Flash memory,
enabling the system to read the boot-up firm-ware from
the Flash memory.
If RESET is asserted during a program or erase
operation, the RY/BY pin remains a "0" (busy) until the
internal reset operation is complete, which requires a time
of tREADY (during Embedded Algorithms). The system
can thus monitor RY/BY to determine whether the reset
operation is complete. If RESET is asserted when a
program or erase operation is not executing (RY/BY pin
is "1"), the reset operation is completed within a time of
tREADY (not during Embedded Algorithms).The system
can read data tRH after the RESET pin returns to VIH.
Refer to the AC Characteristics tables for RESET
parameters and to Figure 14 for the timing diagram.
SECTOR GROUP PROTECT OPERATION
The MX29LV320T/B features hardware sector group pro-
tection. This feature will disable both program and erase
operations for these sector group protected. To activate
this mode, the programming equipment must force VID
on address pin A9 and control pin OE, (suggest V =
ID
12V) A6 = VIL and CE = VIL.(see Table 2) Programming
of the protection circuitry begins on the falling edge of
the WE pulse and is terminated on the rising edge. Please
refer to sector group protect algorithm and waveform.
MX29LV320T/B also provides another method which re-
quires VID on the RESET only.This method can be imple-
mented either in-system or via programming equipment.
This method uses standard microprocessor bus cycle
timing.
To verify programming of the protection circuitry, the pro-
gramming equipment must force VID on address pin A9 (
with CE and OE at VIL and WE at VIH). When A1=1, it
will produce a logical "1" code at device output Q0 for a
protected sector. Otherwise the device will produce 00H
for the unprotected sector. In this mode, the addresses,
except for A1, are don't care. Address locations with
A1= VIL are reserved to read manufacturer and device
codes.(Read Silicon ID)
It is also possible to determine if the group is protected
in the system by writing a Read Silicon ID command.
Performing a read operation with A1=VIH, it will produce
a logical "1" at Q0 for the protected sector.
CHIP UNPROTECT OPERATION
The MX29LV320T/B also features the chip unprotect
mode, so that all sectors are unprotected after chip
unprotect is completed to incorporate any changes in
the code. It is recommended to protect all sectors before
activating chip unprotect mode.
To activate this mode, the programming equipment must
force VID on control pin OE and address pin A9. The CE
pins must be set at VIL. Pins A6 must be set to VIH.(see
Table 2) Refer to chip unprotect algorithm and wave-
form for the chip unprotect algorithm. The unprotection
mechanism begins on the falling edge of the WE pulse
and is terminated on the rising edge.
MX29LV320T/B also provides another method which re-
quires VID on the RESET only.This method can be imple-
mented either in-system or via programming equipment.
This method uses standard microprocessor bus cycle
timing.
It is also possible to determine if the chip is unprotected
in the system by writing the Read Silicon ID command.
P/N:PM0742
REV. 1.4, JUL. 04, 2003
12
12 Page | ||
| Seiten | Gesamt 30 Seiten | |
| PDF Download | [ MX29LV320B Schematic.PDF ] | |
Link teilen
Besondere Datenblatt
| Teilenummer | Beschreibung | Hersteller |
| MX29LV320 | 32M-bit Single Voltage 3V Only Flash Memory | Macronix |
| MX29LV320AB | 3V ONLY FLASH MEMORY | Macronix |
| MX29LV320AT | 3V ONLY FLASH MEMORY | Macronix |
| MX29LV320B | 32M-bit Single Voltage 3V Only Flash Memory | Macronix |
| MX29LV320CB | 32M-BIT [4M x 8 / 2M x 16] SINGLE VOLTAGE 3V ONLY FLASH MEMORY |  Macronix International |
| Teilenummer | Beschreibung | Hersteller |
| CD40175BC | Hex D-Type Flip-Flop / Quad D-Type Flip-Flop. |
 Fairchild Semiconductor |
| KTD1146 | EPITAXIAL PLANAR NPN TRANSISTOR. |
 KEC |
| www.Datenblatt-PDF.com | 2020 | Kontakt | Suche |