Datenblatt-pdf.com


LB1241-12-S1 Schematic ( PDF Datasheet ) - Ledtech

Teilenummer LB1241-12-S1
Beschreibung SQUARE LIGHT BAR
Hersteller Ledtech
Logo Ledtech Logo 




Gesamt 6 Seiten
LB1241-12-S1 Datasheet, Funktion
LEDTECH ELECTRONICS CORP.
NANYA ROAD,MUGANG ZHAOQING
CITY GUANGDONG CHINA.
TEL:86-758-2875541,2870651,2877464,2876185,2877017
FAX:86-758-2878014
Http://www.ledtech.com.tw
SPECIFICATION
PART NO. : LB1241-12-S1 NWRN
1.0"(24.9mm)SQUARE LIGHT BAR
Approved by
Tung
Checked by
Andy
Prepared by
Zhou






LB1241-12-S1 Datasheet, Funktion
LB1241-12-S1
1.0" SQUARE
LIGHT BAR
Precautions in Use:
PLEASE PAY SPECIAL ATTNTION TO THE NEXT POINT TO INCORPORATE OPTO
DEVICE TO HIGH RELIABILITY
1. Do not bend the lead. Bending leads could cause breakage of leads or the degradation of the chip.
When bending is unavoidable, strictly follow the cautionary instruction below.
(1)Bend the leads before soldering.
(2)Bending a lead must be done by fixing a lead tightly and applying no stress on the resin part.
(3) The lead bending point must be more than 1.6mm away from the edge or the resin part.
(4)When a pin is tested for its endurance, bending degree should be repeated no more than two times.
2. Setting a product by using tool such as a holder should be avoided.
When necessary, no stress should be applied to the resin part and lead to consider dimension tolerance,
thermal expansion, thermal contraction of holder, product and circuit board etc.
3. The hole pitch of a circuit board must fit into the lead pitch of products.
4. When soldering, care the followings:
(1)Do not heat a product under any stress (i.e.: twist) to leads.
(2)Do not heat ( for example, by soldering ) a product while out side force is applied the resin part.
(3 The lead bending point must be more than 1.6mm away from the edge or the resin part.
(4)Soldering with PC Board should be conducted with following conditions.
(a) For dip soldering
Pre-heating : 90 Max. for within 60 Sec.
Soldering Max. : 260 5 (Solder Temp.) for within 5 Sec.
(b) Soldering iron : 350
Max.
Cleaning time : 30Sec. Max.
6. Minimum amount of soldering flux should be used. Soldering flux should be applied only to the pin portion.
7. The following may damage products or LED chips: Attachment or contact of residual flux solvent
onto the product surface or to LED chips, or invasion of the same into the product.
VER.: 01 Date: 2007/01/24 Page: 5/5

6 Page







SeitenGesamt 6 Seiten
PDF Download[ LB1241-12-S1 Schematic.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
LB1241-12-S1SQUARE LIGHT BARLedtech
Ledtech

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com       |      2020       |      Kontakt     |      Suche