Datenblatt-pdf.com


LC78211 Schematic ( PDF Datasheet ) - ON Semiconductor

Teilenummer LC78211
Beschreibung Analog Function Switch
Hersteller ON Semiconductor
Logo ON Semiconductor Logo 




Gesamt 6 Seiten
LC78211 Datasheet, Funktion
Ordering number : ENA4817A
LC78211, 78212, 78213
CMOS LSI
Analog Function Switch
http://onsemi.com
Applications
Function switching under serial data control in amplifiers, receivers, and other electronic equipment.
Features
Two sets of eight (or in the LC78213, seven) built-in circuits with three switching configurations available based on
differing internal connections.
Control according to serial data sent from a microprocessor, and easy connection to 5 V microprocessors.
Two identical products can be connected to a shared bus due to the provision of a select pin (S).
A reset pin that turns off all analog switches.
A ±20 V withstand voltage rating allows these products to provide a wide dynamic range.
Specifications
Absolute Maximum Ratings at Ta = 25C
Parameter
Symbol
Conditions
Maximum supply voltage
Maximum input voltage
VDD max
VEE max
VI1
VDD
VEE
DI, CL, CE, S, RES
VI2 L1 to L8, R1 to R8, LCOM1 to LCOM4, RCOM1 to RCOM4
Analog switch potential
difference when on
VON
With the switch on
Ratings
–0.3 to +20
–20 to +0.3
–0.3 to +20
VEE – 0.3 to VDD + 0.3
0.5
Unit
V
V
V
V
V
Allowable power dissipation
Operating temperature range
Storage temperature range
Pd max
Topr
Tstg
Ta 75°C
100
–30 to +75
–40 to +125
mW
C
C
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed,
damage may occur and reliability may be affected.
Package Dimensions
unit : mm
PDIP30 / DIP30SD (400mil)
CASE 646AZ
ORDERING INFORMATION
See detailed ordering and shipping information on page 6 of this data sheet.
Semiconductor Components Industries, LLC, 2013
December, 2013
DIP30SD (400mil)
73096HA (OT)/72994 TH (OT) No.A4817-1/6






LC78211 Datasheet, Funktion
2. DI, CL and CE Timing
LC78211, 78212, 78213
Data is read in on the rising edge of CL and latched on the falling edge of CE.
3. Notes on the Reset Pin
The states of the analog switches are undefined when power is first applied. However, it is possible to use the reset
pin to force all switches to the off state by connecting an RC circuit to this pin.
4. Using a CCB Bus with Multiple ICs
The LC78211, LC78212 and LC78213 retain their prior state until they receive data with a matching address.
5. Replacing Earlier Models
Caution is required when replacing an LC7821N, LC7823N and LC7823N with an LC78211, LC78212 and
LC78213, since the S pin threshold levels differ.
6. Handling of Unused Input Pins
We recommend connecting any unused switch pin to VSS through a resistor of up to a few 100 k to prevent damage
from static electricity.
ORDERING INFORMATION
LC78211-E
Device
LC78212-E
LC78213-E
Package
DIP30SD(400mil)
(Pb-Free / Halogen Free)
DIP30SD(400mil)
(Pb-Free / Halogen Free)
DIP30SD(400mil)
(Pb-Free / Halogen Free)
Shipping (Qty / Packing)
20 / Fan-Fold
20 / Fan-Fold
20 / Fan-Fold
ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number
of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at
www.onsemi.com/site/pdf/Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no
warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the
application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental
damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual
performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts.
SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as
components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any
such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors
harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or
death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the
part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PS No.A4817-6/6

6 Page







SeitenGesamt 6 Seiten
PDF Download[ LC78211 Schematic.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
LC7821Analog Function SwitchSanyo Semicon Device
Sanyo Semicon Device
LC78211Analog Function SwitchSanyo Semicon Device
Sanyo Semicon Device
LC78211Analog Function SwitchON Semiconductor
ON Semiconductor
LC78212Analog Function SwitchSanyo Semicon Device
Sanyo Semicon Device
LC78212Analog Function SwitchON Semiconductor
ON Semiconductor

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com       |      2020       |      Kontakt     |      Suche