|
|
PDF ISL9221 Data sheet ( Hoja de datos )
| Número de pieza | ISL9221 | |
| Descripción | Dual Input Lithium Ion Battery Charger | |
| Fabricantes | Intersil | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de ISL9221 (archivo pdf) en la parte inferior de esta página. Total 11 Páginas | ||
|
No Preview Available !
®
Data Sheet
April 3, 2008
ISL9221
FN6541.1
Dual Input Lithium Ion Battery Charger
with OVP USB Bypass and 10mA LDO
The ISL9221 Lithium Ion charging IC is designed to meet the
charging requirements of most of today’s handheld devices.
The IC provides two inputs for either USB connection where
the current is limited by the USB standard or for
powering/charging from a power adapter.
If the voltage at either VUSB or VDC pin is within the safe
allowable range, the PPR pin is pulled low indicating to the
system processor that external power is available.
Charging can be enabled/disabled by controlling the state of
the EN pin. While charging, the CHG pin is pulled low
indicating the battery is being charged.
The battery is charged to 4.2V with only a 1% error across
the temperature range. USB charge current, Adapter charge
current and charge termination currents can be programmed
via external resistors.
The ISL9221 adds an additional feature in providing a limited
amount of current to system architecture while protecting the
system from destructively high voltage.
The device contains Thermal regulation and protection to
provide additional safety features of this device. When the
temperature exceeds +125°C, the current will fold back to
reduce and control the die temperature.
Ordering Information
PART
NUMBER
(Note)
PART
TEMP.
MARKING RANGE (°C)
PACKAGE PKG.
(Pb-Free) DWG. #
ISL9221IRZ 9221
-40°C to +85°C 12 Ld 4x3 DFN L12.4x3
ISL9221IRZ-T* 9221
-40°C to +85°C 12 Ld 4x3 DFN L12.4x3
*Please refer to TB347 for details on reel specifications.
NOTE: These Intersil Pb-free plastic packaged products employ
special Pb-free material sets; molding compounds/die attach materials
and 100% matte tin plate PLUS ANNEAL - e3 termination finish, which
is RoHS compliant and compatible with both SnPb and Pb-free
soldering operations. Intersil Pb-free products are MSL classified at
Pb-free peak reflow temperatures that meet or exceed the Pb-free
requirements of IPC/JEDEC J STD-020.
Features
• Lithium Ion/Polymer battery charging
• Dual input - USB host or car/wall adapter
• Input voltage withstanding up to 28V
• 5.4V overvoltage protection on VUSB inputs
• Charging current up to 1.2A
• 4.9V/10mA linear regulator with input OVP
• Current limit on bypass path
• Programmable end-of-charge current
• Programmable charging current
• Programmable USB current limit
• Charging and power present indicator pins
• Charge enable pin
• Reverse current protection
• Pb-free (RoHS compliant)
Applications
• Smart Handheld Devices
• Cell Phones, PDAs, MP3 Players
• Digital Still Cameras
• Handheld Test Equipment
Related Literature
• Technical Brief TB363 “Guidelines for Handling and
Processing Moisture Sensitive Surface Mount Devices
(SMDs)”
• Technical Brief TB389 “PCB Land Pattern Design and
Surface Mount Guidelines for QFN Packages”
Pinout
ISL9221
(12 LD DFN)
TOP VIEW
VDC 1
VUSB 2
PPR 3
CHG 4
EN 5
IMIN 6
12 VDC_LDO
11 BAT
10 USB_BYP
9 IVDC
8 GND
7 IUSB
1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2008. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
1 page  
ISL9221
The USB_BYP and VDC_LDO stay on regardless of the
state of this pin. This ensures that the processor can be
powered up when an external source is connected to the
VDC or VUSB input pin.
PPR
Power presence indication pin. This pin is used to notify the
system processor or enable the power circuitry when a
source is connected. The pin is an open drain output pin,
which pulls low when a valid voltage (above POR) is present
at either the VDC or VUSB pin. The PPR pin is held low
regardless of the state of the EN pin. If connected to the
processor, a pull-up resistor should be connected to the
processors I/O supply. If connected to power circuitry, a
pull-up should be tied to the appropriate bypass supply.
Typical Application
CHG
Charge indication pin. This open-drain pin is pulled low to
indicate when the battery is being charged. If connected to
the processor, a pull-up resistor should be connected to the
processors I/O supply.
The CHG pin can also be used to drive an LED to indicate to
the user the battery is being charged.
GND
Ground pin. This provides the ground path for all internal
circuits.
LDO OUTPUT
VDC INPUT
USB INPUT
USB_BYP
OFF
ON
VDC
VUSB
ISL9221
BAT
GND
FIGURE 1. APPLICATIONS CIRCUIT
TO MCU
TO BATTERY
5 FN6541.1
April 3, 2008
5 Page 
ISL9221
Dual Flat No-Lead Plastic Package (DFN)
2X
0.15 C A
AD
2X
0.15 C B
6
INDEX
AREA
TOP VIEW
E
B
C SIDE VIEW
SEATING
PLANE
(DATUM B)
6
INDEX
AREA
(DATUM A)
D2
D2/2
12
// 0.10 C
A
0.08 C
A3
78
NX k
E2
E2/2
NX L
8
N N-1
e
(Nd-1)Xe
REF.
BOTTOM VIEW
NX (b)
5
(A1)
SECTION "C-C" TERMINAL TIP
NX b
5
0.10 M C A B
CL
L
e
FOR EVEN TERMINAL/SIDE
L12.4x3
12 LEAD DUAL FLAT NO-LEAD PLASTIC PACKAGE
(COMPLIANT TO JEDEC MO-229-VGED-4 ISSUE C)
MILLIMETERS
SYMBOL
MIN NOMINAL MAX
NOTES
A 0.80 0.90 1.00
-
A1
-
- 0.05
-
A3 0.20 REF -
b 0.18 0.23 0.30
5,8
D
4.00 BSC
-
D2 3.15 3.30 3.40
7,8
E
3.00 BSC
-
E2 1.55 1.70 1.80
7,8
e
0.50 BSC
-
k 0.20 - - -
L 0.30 0.40 0.50
8
N 12 2
Nd 6 3
NOTES:
Rev. 1 2/05
1. Dimensioning and tolerancing conform to ASME Y14.5-1994.
2. N is the number of terminals.
3. Nd refers to the number of terminals on D.
4. All dimensions are in millimeters. Angles are in degrees.
5. Dimension b applies to the metallized terminal and is measured
between 0.15mm and 0.30mm from the terminal tip.
6. The configuration of the pin #1 identifier is optional, but must be
located within the zone indicated. The pin #1 identifier may be
either a mold or mark feature.
7. Dimensions D2 and E2 are for the exposed pads which provide
improved electrical and thermal performance.
8. Nominal dimensions are provided to assist with PCB Land
Pattern Design efforts, see Intersil Technical Brief TB389.
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
11 FN6541.1
April 3, 2008
11 Page | ||
| Páginas | Total 11 Páginas | |
| PDF Descargar | [ Datasheet ISL9221.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| ISL9220 | Switching Charger | Intersil |
| ISL9220A | Switching Charger | Intersil |
| ISL9220B | Switching Charger |  Intersil Corporation |
| ISL9221 | Dual Input Lithium Ion Battery Charger | Intersil |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |