|
|
Teilenummer | V400H1-P08 |
|
Beschreibung | TFT LCD Module | |
Hersteller | CMI MEI | |
Logo | ||
Gesamt 28 Seiten Global LCD Panel Exchange Center
www.panelook.com
PRODUCT SPECIFICATION
ϭʳ Tentative Specification
ϭʳ Preliminary Specification
Ϯʳ Approval Specification
MODEL NO.: V400H1
SUFFIX: P08
Customer:
APPROVED BY
Name / Title
Note
SIGNATURE
Please return 1 copy for your confirmation with your
signature and comments.
Approved By
Chao-Chun Chung
Checked By Prepared By
Josh Chi Joanne Chung
Version 2.0
1 DateΚ9 Jun 2010
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT SPECIFICATION
2. ABSOLUTE MAXIMUM RATINGS
2.1 ABSOLUTE RATINGS OF ENVIRONMENT (BASE ON CMO MODULE V400H1-L08)
Value
Item Symbol
Unit
Min. Max.
Note
Storage Temperature
TST -20
+60 ºC (1)
Operating Ambient Temperature
TOP
0
50 ºC (1), (2)
Shock (Non-Operating)
SNOP
-
30 G (3), (5)
Vibration (Non-Operating)
VNOP
-
1.0 G (4), (5)
Note (1) Temperature and relative humidity range is shown in the figure below.
(a) 90 %RH Max. (Ta Љ 40 ºC).
(b) Wet-bulb temperature should be 39 ºC Max. (Ta > 40 ºC).
(c) No condensation.
Note (2) The maximum operating temperature is based on the test condition that the surface temperature of
display area is less than or equal to 65 ºC with LCD module alone in a temperature controlled chamber.
Thermal management should be considered in final product design to prevent the surface temperature
of display area from being over 65 ºC. The range of operating temperature may degrade in case of
improper thermal management in final product design.
Note (3) 11 ms, half sine wave, 1 time for ± X, ± Y, ± Z.
Note (4) 10 ~ 200 Hz, 10 min, 1 time each X, Y, Z.
Note (5) At testing Vibration and Shock, the fixture in holding the module has to be hard and rigid enough so that
the module would not be twisted or bent by the fixture.
Version 2.0
6 DateΚ9 Jun 2010
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
6 Page Global LCD Panel Exchange Center
www.panelook.com
PRODUCT SPECIFICATION
Note (1) Two pixel data send into the module for every clock cycle. The first pixel of the frame is odd pixel and
the second pixel is even pixel
Note (2) LVDS connector pin order defined as follows
Note (3) Reserved for internal use. Please leave it open.
Note (4) Low: JEIDA LVDS Format (Connect to GND), High or open: VESA Format. (Connect to +3.3V)
Note (5) LVDS signal pin connected to the LCM side has the following diagram.
R1 in the system side should be less than 1K Ohm. (R1 < 1K Ohm)
Selector (pin45)
R1
Vcc
TCON
R3
R2
Setting
System side
System side
R1 < 1K
LCM side
Version 2.0
12 DateΚ9 Jun 2010
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
12 Page | ||
Seiten | Gesamt 28 Seiten | |
PDF Download | [ V400H1-P08 Schematic.PDF ] |
Teilenummer | Beschreibung | Hersteller |
V400H1-P02 | TFT LCD Module | CMI MEI |
V400H1-P08 | TFT LCD Module | CMI MEI |
Teilenummer | Beschreibung | Hersteller |
CD40175BC | Hex D-Type Flip-Flop / Quad D-Type Flip-Flop. |
Fairchild Semiconductor |
KTD1146 | EPITAXIAL PLANAR NPN TRANSISTOR. |
KEC |
www.Datenblatt-PDF.com | 2020 | Kontakt | Suche |