M270DAN01.0 Datasheet PDF - AUO
| Part Number | M270DAN01.0 | |
| Description | Color TFT-LCD | |
| Manufacturers | AUO | |
| Logo |  |
|
|
There is a preview and M270DAN01.0 download ( pdf file ) link at the bottom of this page. Total 30 Pages | ||
Preview 1 page No Preview Available !
Product Specification
AU OPTRONICS CORPORATION
M270DAN01.0
( ) Preliminary Specification
(V) Final Specification
Module
Model Name
27.0” Color TFT-LCD
M270DAN01.0
Customer
Date
Approved by
Howard Lee
Date
Approved by
Prepared by
Shin Yu Lin
2013/4/16
Note: This Specification is subject to change
without notice.
AU Optronics Corporation
document version 0.6
1
|
| |
 
Product Specification
AU OPTRONICS CORPORATION
1 Handling Precautions
M270DAN01.0
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth
when handling.
7) Do not open or modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a Module has to be put back into the packing container slot after once it was taken out
from the container, do not press the center of LED light bar edge. Instead, press at the far ends
of the LED light bar edge softly. Otherwise the TFT Module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the
Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure, do not twist nor bend the TFT Module
even momentary. At designing the enclosure, it should be taken into consideration that no
bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT Module
may be damaged.
12) Small amount of materials having no flammability grade is used in the LCD module. The LCD
module should be supplied by power complied with requirements of Limited Power Source
(IEC60950 or UL1950), or be applied exemption.
13) Avoid touching COF position while doing mechanical design.
14) Avoid stressing front bezel position when doing mechanical design
15) While storing modules as spares for a long time, the following precautions are necessary:
Store modules in a dark place. Do not expose them to sunlight or fluorescent light.
Keep the temperature between 5°C and 35°C at normal humidity.
document version 0.6
5
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for M270DAN01.0 electronic component. |
| Information | Total 30 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ M270DAN01.0.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| M270DAN01.0 | The function is Color TFT-LCD. AUO | |
| M270DAN01.1 | The function is Color TFT-LCD. AUO | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
M270
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||