Datenblatt-pdf.com


AM-480800-043A Schematic ( PDF Datasheet ) - AMSON

Teilenummer AM-480800-043A
Beschreibung Display Module
Hersteller AMSON
Logo AMSON Logo 




Gesamt 21 Seiten
AM-480800-043A Datasheet, Funktion
AM-480800-043A
Version: C
2013-08-29
Specification for Approval
Customer:
Model Name:
Supplier Approval
Customer approval
R&D Designed R&D Approved QC Approved
Peter Peng Jun
YU DU AMSON ELECTRONICS CO.,LTD.
Page 1 of 21






AM-480800-043A Datasheet, Funktion
AM-480800-043A
Version: C
2013-08-29
4. Interface Description
Pin Symbol
Description.
1 LEDK LED backlight (Cathode).
2 LEDA LED backlight (Anode).
3 NC No connection.
4 NC No connection.
5 NC No connection.
6 NC No connection.
7 GND Power ground
8 VCC Analog supply voltage to the analog circuit.
9 NC No connection.
10 IOVCC Logic supply voltage to the logic circuit.
11 TE Tearing effect output pin to synchronize MCU to frame writing.
12 SDO Serial output signal in SPI I/F.
13 SDI Serial input signal in SPI I/F.
14
WRX_DCX
Writes strobe signal to write data when WRX is “Low” in MPU I/F.
Date/Command Selection pin in 4-wire SPI I/F.
15 CSX Chip select input pin (“Low” enable) in MPU I/F and SPI I/F.
16 RESX Reset input pin, Active “L”.
17 DB23
18 DB22
19 DB21
20 DB20
21 DB19
22 DB18
23 DB17
24 DB16
25
26
DB15
DB14
24-bit parallel bi-directional data bus for MPU system:
8-bit I/F: DB[7:0] is used.
16-bit I/F: DB[15:0] and DB[8:1] is used.
27 DB13 24-bit I/F: DB[23:0] is used.
28 DB12
29 DB11 24-bit input data bus for RGB I/F.
30 DB10 16-bit/pixel: DB[20:16]=R[4:0], DB[13:8]=G[5:0] and DB[5:1]=B[4:0];
31
32
DB09
DB08
18-bit/pixel: DB[21:16]=R[5:0], DB[13:8]=G[5:0] and DB[5:0]=B[5:0];
24-bit/pixel: DB[23:16]=R[7:0], DB[15:8]=G[7:0] and DB[7:0]=B[7:0].
Connect unused pins to GND.
33 DB06
34 DB07
35 DB05
36 DB04
37 DB03
38 DB02
39 DB01
40 DB00
YU DU AMSON ELECTRONICS CO.,LTD.
Page 6 of 21

6 Page









AM-480800-043A pdf, datenblatt
AM-480800-043A
Version: C
2013-08-29
9. Optical Characteristics
Optical characteristics are determined after the unit has been ‘ON’ and stable for
approximately 30 minutes in a dark environment at 25 °C. The values specified are at an
approximate distance 50cm from the TFT-LCD surface at a viewing angle of Φ and θ equal to 0°.
Measurement condition: Refer to next pages (LED back light with 20 mA/1 ea)
*1): with LGD Polarizer;
*2): Only Color Filter glass
Notes:
1. Contrast Ratio (CR) is defined mathematically as:
Contrast Ratio =
Surface Luminance with all white pixels
Surface Luminance with all black pixels
2. Surface luminance is the center point across the TFT-LCD surface 500mm from the surface
with all pixels displaying white. For more information see FIG 1.
3. Response time is the time required for the display to transition from white to black (Rise Time,
Tr) and from black to white (Falling Time, Tf). For additional information see FIG 3.
4. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are
determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which
is normal to the TFT-LCD surface. For more information see FIG 5.
5. Optimum contrast is obtained by adjusting the TFT-LCD threshold voltage (Vth & Vsat).
YU DU AMSON ELECTRONICS CO.,LTD.
Page 12 of 21

12 Page





SeitenGesamt 21 Seiten
PDF Download[ AM-480800-043A Schematic.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
AM-480800-043ADisplay ModuleAMSON
AMSON

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com       |      2020       |      Kontakt     |      Suche