Datenblatt-pdf.com


PJ550 Schematic ( PDF Datasheet ) - ViewSonic

Teilenummer PJ550
Beschreibung High Brightness Light Weight LCD Projector User Guide Manual
Hersteller ViewSonic
Logo ViewSonic Logo 




Gesamt 30 Seiten
PJ550 Datasheet, Funktion
PJ500/PJ550
PJ501/PJ551
User Guide
Image Size 30” - 300”
High Brightness Light Weight
LCD Projector






PJ550 Datasheet, Funktion
Projector Components
Projector Components Diagram
Slot for Kensington Lock
Power switch
AC power
Intake ventilation
Control panel
Reset
Keystone
Input
Standby/ON
Front foot adjuster
Air intake
(for the cooling fan)
Speaker
Rear foot
adjuster
Remote control
sensor
Component Video
Y (In)
CB/PB (In)
CR/PR (In)
S-Video (In)
Zoom knob
Focus ring
Remote control
sensor
Lens (with lens cap)
Lamp indicator
Temp indicator
Power indicator
Menu
Exhaust ventilation
Interface
panel
RGB (In)
Control (RS232)
Audio (In, 3.5 mm)
R Audio (In)
L Audio (In)
Video (In)
Figure 2: Projector Components
3 ViewSonic PJ500/PJ550/PJ501/PJ551

6 Page









PJ550 pdf, datenblatt
Operations
Power ON
NOTE: Refer to “Example of System Setup” on page 8.
1 Make sure the power cord is connected correctly and lens cap has been removed. Set the Power
Switch to [I] ON. The unit is now in Standby mode and the POWER indicator LED turns a
steady orange.
2 Press the STANDBY/ON button on the control panel or the remote control. Warm-up begins and
the power indicator blinks in green.
3 After several seconds the lamp will stop blinking and will turn to continuous green, indicating
that the projector is ready to use.
4 Adjust the size of the projected image with the Zoom knob.
5 Adjust focus using the Focus ring.
Power OFF
NOTE: See Caution below.
1 Press the STANDBY/ON button on the control panel or the remote control. The message
“POWER OFF?” will display on the screen, and the message will disappear in 5 seconds. During
this message indication, press the STANDBY/ON button again. The projector lamp shuts off and
lamp cooling begins.
2 Wait for the cooling fan to stop. The POWER indicator blinks orange during lamp cooling.
Pressing the STANDBY/ON button has no effect while the POWER indicator is blinking.
3 The system assumes the Standby mode when cooling is complete. The POWER indicator ceases
blinking and changes to a steady orange. Check that the indicator is orange and set the POWER
switch to [O]. The POWER indicator turns off when the Power Switch is set to [O] OFF.
Remember to replace the lens cap after use.
Power Indicator
Standby/On Button
Zoom Knob
Focus Ring
Remote Control
Power Switch
Figure 9: Power Buttons
NOTE: Except in emergencies, do not turn off the Power Switch unless the POWER indicator is a
steady orange. Otherwise improper cooling of the lamp will reduce the life of the lamp or may
damage the lamp.
CAUTION
• To turn OFF the projector press the Standby/ON button and hold for 2 seconds .
• The POWER LED on the control pad flashes orange during cool-down.
• Wait until the POWER LED changes to a steady orange before you set the Power Switch to [O] OFF.
9 ViewSonic PJ500/PJ550/PJ501/PJ551

12 Page





SeitenGesamt 30 Seiten
PDF Download[ PJ550 Schematic.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
PJ550High Brightness Light Weight LCD Projector User Guide ManualViewSonic
ViewSonic
PJ551High Brightness Light Weight LCD Projector User Guide ManualViewSonic
ViewSonic

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com       |      2020       |      Kontakt     |      Suche