Datenblatt-pdf.com


EUA4890MIR1 Schematic ( PDF Datasheet ) - Eutech Microelectronics

Teilenummer EUA4890MIR1
Beschreibung 1 Watt Audio Power Amplifier
Hersteller Eutech Microelectronics
Logo Eutech Microelectronics Logo 




Gesamt 14 Seiten
EUA4890MIR1 Datasheet, Funktion
EUA4890
1 Watt Audio Power Amplifier
DESCRIPTION
The EUA4890 is an audio power amplifier designed for
portable communication device applications such as
mobile phone applications. The EUA4890 is capable of
delivering 1.0W of continuous average power to an 8
BTL and with less than 1% distortion (THD+N) from a
5.0V power supply, and 350mW to a 8BTL load from a
3V power supply.
The EUA4890 provides high quality audio while requiring
few external components and minimal power consumption.
It features a low-power shutdown mode, which is achieved
by driving the SHUTDOWN pin with logic low.
The EUA4890 contains circuitry to prevent from ”pop and
click” noise that would otherwise occur during turn-on and
turn-off transitions.
For maximum flexibility, the EUA4890 provides an
externally controlled gain (with resistors), as well as an
externally controlled turn-on and turn-off times (with the
bypass capacitor).
The EUA4890 is available in a MSOP-8 , 3mm×3mm DFN
package.
FEATURES
z 2.5-5.5V operation
z 65dB PSRR at 217Hz, VDD=5V
z 0.1µA ultra low current shutdown mode
z Improved pop & click circuitry
z No output coupling capacitors, snubber networks or
bootstrap capacitors required
z Thermal shutdown protection
z Unity-gain stable
z External gain configuration capability
z BTL output can drive capacitive loads
z RoHS compliant and 100% lead(Pb)-free
APPLICATIONS
z Mobile Phones
z PDAs
z Portable electronic devices
Block Diagram
DS4890 Ver 1.7 Dec. 2006
Figure1.
1






EUA4890MIR1 Datasheet, Funktion
EUA4890Tel: 0755-8398 3377 / 135 9011 2223 http://www.gofotech.com
Electrical Characteristics VDD = 3V, TA = 25°C
Symbol
Parameter
Conditions
IDD Quiescent Power Supply Current
ISD Shutdown Current
VSDIH Shutdown Voltage Input High
VSDIL Shutdown Voltage Input Low
VOS Output Offset Voltage
ROUT-GND Resistor Output to GND
PO
TWU
TSD
THD+N
Output Power (8)
Wake-up time
Thermal Shutdown Temperature
Total Harmonic Distortion + Noise
PSRR Power Supply Rejection Ratio
VIN=0V, IO=0A, No load
VIN=0V, IO=0A, 8load
VSHUTDOWN=0V
THD=1%; f=1kHz
PO=0.15 Wrms; f=1kHz
Vripple=200mV sine p-p
Input Terminated with 10 ohms
to ground
EUA4890
Min Typ Max.
1.8 4
1.9 4
0.1 2.0
1.2
0.4
5 25
7.0 8.5 9.7
0.28 0.35
120 180
150 170
0.15
65(f=217
45
Hz)
66(f=1kH
z)
Unit
mA
mA
µA
V
V
mV
k
W
ms
°C
%
dB
Electrical Characteristics VDD = 2.6V, TA = 25°C
Symbol
Parameter
Conditions
IDD Quiescent Power Supply Current
ISD Shutdown Current
Output Power (8)
PO Output Power (4)
THD+N Total Harmonic Distortion + Noise
PSRR Power Supply Rejection Ratio
VIN=0V, IO=0A, No load
VSHUTDOWN=0V
THD=1%; f=1kHz
THD=1%; f=1kHz
PO=0.1Wrms; f=1kHz
Vripple=200mV sine p-p
Input Terminated with 10 ohms
to ground
EUA4890
Min Typ Max.
1.7
0.1
0.25
0.32
0.15
55(f=217
Hz)
56(f=1kH
z)
Unit
mA
µA
W
%
dB
DS4890 Ver 1.7 Dec. 2006
6

6 Page









EUA4890MIR1 pdf, datenblatt
EUA4890Tel: 0755-8398 3377 / 135 9011 2223 http://www.gofotech.com
Application Information
Bridged Configuration Explanation
The structure of the EUA4890 is basically composed of
two identical internal power amplifiers; the first one si
externally configurable with gain-setting resistors Rin and
Rf (the closed-loop gain is fixed by the ratios of theses
resistors) and the second is internally fixed in an inverting
unity-gain configuration by two resistors of 20k. So the
load is driven differentially through OUTA and OUTB
outputs. This configuration eliminates the need for an
output coupling capacitor.
The differential-ended amplifier presents two major
advantages:
- The possible output power is four times larger (the
output swing is doubled) as compared to single-ended
amplifier under the same conditions.
- Output pins (OUTA and OUTB) are biased at the
same potential VDD/2, this eliminates the need for an
output coupling capacitor required with a
single-ended amplifier configuration.
The differential closed loop-gain of the amplifier is
given by Avd=
2 × R f = Vorms
R Vinrms
in
Power Dissipation
Power dissipation is a major concern when designing a
successful amplifier, whether the amplifier is bridged or
single-ended. A direct consequence of the increased
power delivered to the load by a bridge amplifier is an
increase in internal power dissipation. Since the
EUA4890 has two operational amplifiers in one package,
the maximum internal power dissipation is 4 times that of
a single-ended amplifier. The maximum power dissipation
for a given application can be derived from the power
dissipation graphs of from equation1.
PDMAX = 4 * (VDD )2 /(2π 2R L ) ------------(1)
It is critical that the maximum junction temperature TJMAX
of 150°C is not exceeded. TJMAX can be determine from
the power derating curves by using PDMAX and the PC
board foil area. By adding additional copper foil, the
thermal resistance of the application can be reduced,
resulting in higher PDMAX. Additional copper foil can be
added to any of the leads connected to the EUA4890.If
TJMAX still exceeds 150°C, then additional changes must
be made. These changes can include reduced supply
voltage, higher load impedance, or reduced ambient
temperature. Internal power dissipation is a function of
output power.
Proper Selection of External Components
The EUA4890 is unity-gain stable and requires no
external components besides gain-setting resistors, and
input coupling capacitor and proper bypassing capacitor
in the typical application.
Gain-Setting Resistor Selection (Rin and Rf)
Rin and Rf set the closed-loop gain of the amplifier.
In order to optimize device and system performance, the
EUA4890 should be used in low gain configurations.
The low gain configuration minimizes THD + noise
values and maximizes the signal to noise ratio, and the
amplifier can still be used without running into the
bandwidth limitations. Low gain configurations require
large input signals to obtain a given output power. Input
signals equal to or greater than 1Vrms are available from
sources such as audio codecs.
A closed loop gain in the range from 2 to 5 is
recommended to optimize overall system performance.
An input resistor (Rin) value of 20kis realistic in most
of applications, and does not require the use of a too large
capacitor Cin.
Input Capacitor Selection (Cin)
The input coupling capacitor blocks the DC voltage at the
amplifier input terminal. This capacitor creates a
high-pass filter with Rin, the cut-off frequency is given by
fc = 1
2 * *R in * Cin
The size of the capacitor must be large enough to couple
in low frequencies without severe attenuation. However a
large input coupling capacitor requires more time to reach
its quiescent DC voltage (VDD/2) and can increase the
turn-on pops.
An input capacitor value between 0.1µ and 0.39µF
performs well in many applications (with Rin=22k).
Bypass Capacitor Selection (Cby)
The bypass capacitor Cby provides half-supply filtering
and determines how fast the EUA4890 turns on.
This capacitor is critical component to minimize the
turn-on pop. A 1.0µF bypass capacitor value (Cin=
0.39µF) should produce clickless and popless shutdown
transitions. The amplifier is still functional with a 0.1µF
capacitor value but is more susceptible to pop and click
noise. Thus, a 1.0µF bypassing capacitor is recommended.
Power Supply Bypassing (CS)
As with any amplifier, proper supply bypassing is critical
for low noise performance and high power supply
rejection. The capacitor location on both the bypass and
power supply pins should be as close to the device is
possible.
DS4890 Ver 1.7 Dec. 2006
12

12 Page





SeitenGesamt 14 Seiten
PDF Download[ EUA4890MIR1 Schematic.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
EUA4890MIR11 Watt Audio Power AmplifierEutech Microelectronics
Eutech Microelectronics

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com       |      2020       |      Kontakt     |      Suche