|
|
Número de pieza | NN-G61AR | |
Descripción | Microwave Oven Service Manual | |
Fabricantes | Panasonic | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de NN-G61AR (archivo pdf) en la parte inferior de esta página. Total 20 Páginas | ||
No Preview Available ! ORDER NO. DCS-JUL2002-002-MS
Service Manual
Microwave Oven
NN-G61 AR
Specifications
Power Source:
220 V AC, 50 Hz
Power requirement:
Microwave: 1.450 W
Heater:
860 W
Output:
Microwave: 900 W: Full Power (IEC 705-88)
Heater:
800 W
Microwave Frequency:
2.450 MHz
Timer:
99 min. 99 sec.
Outside Dimensions:
306 (W) x 555 (D) x 428 (H) mm
Oven Cavity Dimensions:
31 liters
Weight:
Approx. 18 Kg
Specifications subject to change without notice
Panasonic do Brasil Ltda.
CS / DST - 2002
1 page COMPONENT TEST PROCEDURE
NN-G61 AR
CAUTION
1. High voltage is present at the high voltage terminal of
the high voltage transformer during any cook cycle.
2. It is neither necessary nor advisable to attempt
measurement of the high voltage.
3. Before touching any oven components or wiring, always
unplug the oven from its power source and discharge
the high voltage capacitor.
High voltage transformer
1. Remove connections from the transformer terminals and check
continuity.
2. Normal (cold) resistance readings should be as follows:
Secondary winding Approx. 80Ω; ~ 120Ω;
Filament winding Approx. 0Ω;
Primary winding (0v ~ 230/240V) Approx. 0Ω; ~ 3Ω;
Diode
1. Isolate the diode assembly from the circuit by disconnecting
the leads.
2. With the ohmmeter set on the highest resistance scale,
measure the resistance across the diode terminals. Reverse
the meter leads and again observe the resistance reading.
Meter with 6V, 9V or higher voltage batteries should be used
to check the front-to-back resistance of the diode, otherwise
an infinite resistance may be read in both directions. A normal
diodes resistance will be infinite in one direction and several
hundred KΩ; in the order direction.
Magnetron
Continuity checks can only indicate an open filament or a shorted
magnetron. To diagnose for an open filament or shorted
magnetron.
1. Isolate magnetron from the circuit by disconnecting the leads.
2. A continuity check across magnetron filament terminals should
indicate one ohm or less.
3. A continuity check between each filament terminal and
magnetron case should read open.
High voltage capacitor
2. Check continuity of capacitor with ohmmeter on highest ohm scale.
2. A normal capacitor will show continuity for a short time, and
then indicate 9MΩ; once the capacitor is charged.
3. A shorted capacitor will show continuous continuity.
4. An open capacitor will show constant 9MΩ;.
(Due to internal 9MΩ; resistor)
5. Resistance between each terminal and chassis should be infinite.
Membrane key board (Membrane switch assembly)
Check continuity between switch terminals, by pressing an
appropriate pad on the key board.
The contacts assignment of the respective pads on the key board
is as shown in the schematic diagram.
Protector diode
1. Isolate the protector diode assembly from the circuit by
disconnecting its leads.
2. With the ohmmeter set on the highest resistance scale,
measure the resistance across the protector diode terminals.
Reverse the meter leads and again observe the resistance
reading. A normal protector diodes resistance will be infinite in
both directions. It is faulty if it shows continuity in one or both
directions.
-5-
5 Page OVEN EXPLODED VIEW
NN-G61 AR
- 11 -
11 Page |
Páginas | Total 20 Páginas | |
PDF Descargar | [ Datasheet NN-G61AR.PDF ] |
Número de pieza | Descripción | Fabricantes |
NN-G61AR | Microwave Oven Service Manual | Panasonic |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |