|
|
Teilenummer | 74HCT123 |
|
Beschreibung | Dual retriggerable monostable multivibrator | |
Hersteller | NXP Semiconductors | |
Logo | ||
Gesamt 24 Seiten 74HC123; 74HCT123
Dual retriggerable monostable multivibrator with reset
Rev. 10 — 3 December 2015
Product data sheet
1. General description
The 74HC123; 74HCT123 are high-speed Si-gate CMOS devices and are pin compatible
with Low-power Schottky TTL (LSTTL). They are specified in compliance with JEDEC
standard no. 7A.
The 74HC123; 74HCT123 are dual retriggerable monostable multivibrators with output
pulse width control by three methods:
1. The basic pulse is programmed by selection of an external resistor (REXT) and
capacitor (CEXT).
2. Once triggered, the basic output pulse width may be extended by retriggering the
gated active LOW-going edge input (nA) or the active HIGH-going edge input (nB). By
repeating this process, the output pulse period (nQ = HIGH, nQ = LOW) can be made
as long as desired. Alternatively an output delay can be terminated at any time by a
LOW-going edge on input nRD, which also inhibits the triggering.
3. An internal connection from nRD to the input gates makes it possible to trigger the
circuit by a HIGH-going signal at input nRD as shown in Table 3.
Schmitt-trigger action in the nA and nB inputs, makes the circuit highly tolerant to slower
input rise and fall times.
The 74HC123; 74HCT123 are identical to the 74HC423; 74HCT423 but can be triggered
via the reset input.
2. Features and benefits
DC triggered from active HIGH or active LOW inputs
Retriggerable for very long pulses up to 100 % duty factor
Direct reset terminates output pulse
Schmitt-trigger action on all inputs except for the reset input
ESD protection:
HBM JESD22-A114F exceeds 2000 V
MM JESD22-A115-A exceeds 200 V
Specified from 40 C to +85 C and from 40 C to +125 C
NXP Semiconductors
74HC123; 74HCT123
Dual retriggerable monostable multivibrator with reset
8. Recommended operating conditions
Table 5. Recommended operating conditions
Symbol Parameter
Conditions
VCC
VI
VO
t/V
Tamb
supply voltage
input voltage
output voltage
input transition rise and
fall rate
ambient temperature
nRD input
VCC = 2.0 V
VCC = 4.5 V
VCC = 6.0 V
9. Static characteristics
74HC123
Min Typ Max
2.0 5.0 6.0
0 - VCC
0 - VCC
74HCT123
Min Typ Max
4.5 5.0 5.5
0 - VCC
0 - VCC
Unit
V
V
V
- - 625 - - - ns/V
- 1.67 139 - 1.67 139 ns/V
- - 83 - - - ns/V
40 +25 +125 40 +25 +125 C
Table 6. Static characteristics
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Symbol Parameter Conditions
25 C
40 C to +85 C 40 C to +125 C Unit
Min Typ Max Min Max Min Max
74HC123
VIH HIGH-level VCC = 2.0 V
input voltage VCC = 4.5 V
1.5 1.2 -
1.5
-
1.5
3.15 2.4 - 3.15 - 3.15
-V
-V
VCC = 6.0 V
4.2 3.2 -
4.2
-
4.2
-V
VIL LOW-level VCC = 2.0 V
input voltage VCC = 4.5 V
- 0.8 0.5
-
0.5
-
- 2.1 1.35 - 1.35 -
0.5 V
1.35 V
VCC = 6.0 V
- 2.8 1.8
-
1.8
-
1.8 V
VOH HIGH-level VI = VIH or VIL
output voltage IO = 20 A; VCC = 2.0 V
1.9 2.0 -
1.9
-
1.9
-V
IO = 20 A; VCC = 4.5 V
4.4 4.5 -
4.4
-
4.4
-V
IO = 20 A; VCC = 6.0 V
5.9 6.0 -
5.9
-
5.9
-V
IO = 4 mA; VCC = 4.5 V
3.98 4.32 - 3.84
-
3.7
-V
IO = 5.2 mA; VCC = 6.0 V 5.48 5.81 - 5.34
-
5.2
-V
VOL
LOW-level
VI = VIH or VIL
output voltage IO = 20 A; VCC = 2.0 V
- 0 0.1 -
0.1
-
0.1 V
IO = 20 A; VCC = 4.5 V
- 0 0.1 -
0.1
-
0.1 V
IO = 20 A; VCC = 6.0 V
- 0 0.1 -
0.1
-
0.1 V
IO = 4 mA; VCC = 4.5 V
- 0.15 0.26 - 0.33 -
0.4 V
IO = 5.2 mA; VCC = 6.0 V
- 0.16 0.26 -
0.33
-
0.4 V
II
input leakage VI = VCC or GND; VCC = 6.0 V -
- 0.1 -
1.0
-
1.0 A
current
ICC supply current VI = VCC or GND; IO = 0 A;
- - 8.0 -
80
-
160 A
VCC = 6.0 V
74HC_HCT123
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 10 — 3 December 2015
© NXP Semiconductors N.V. 2015. All rights reserved.
6 of 24
6 Page NXP Semiconductors
11. Waveforms
74HC123; 74HCT123
Dual retriggerable monostable multivibrator with reset
9,
Q%LQSXW
*1'
90
W:
9,
Q$LQSXW
*1'
90
W:
9,
Q5'LQSXW
*1'
W3/+
W3/+
90
W:
92+
Q4RXWSXW
92/
92+
Q4RXWSXW
92/
90
W:
90
W3+/
W3+/
9<
W7+/
9;
9<
9;
W7/+
W3+/
UHVHW
W:
W3/+
UHVHW
W3/+
W3+/
DDD
Fig 9.
Measurement points are given in Table 8.
VOL and VOH are typical voltage output levels that occur with the output load.
Propagation delays from inputs (nA, nB, nRD) to outputs (nQ, nQ) and output transition times
74HC_HCT123
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 10 — 3 December 2015
© NXP Semiconductors N.V. 2015. All rights reserved.
12 of 24
12 Page | ||
Seiten | Gesamt 24 Seiten | |
PDF Download | [ 74HCT123 Schematic.PDF ] |
Teilenummer | Beschreibung | Hersteller |
74HCT123 | Dual retriggerable monostable multivibrator with reset | Philips |
74HCT123 | Dual retriggerable monostable multivibrator | NXP Semiconductors |
74HCT123-Q100 | Dual retriggerable monostable multivibrator | NXP Semiconductors |
74HCT125 | Quad buffer/line driver 3-state | Philips |
74HCT125 | QUADRUPLE 3-STATE BUFFERS OE LOW | Diodes |
Teilenummer | Beschreibung | Hersteller |
CD40175BC | Hex D-Type Flip-Flop / Quad D-Type Flip-Flop. |
Fairchild Semiconductor |
KTD1146 | EPITAXIAL PLANAR NPN TRANSISTOR. |
KEC |
www.Datenblatt-PDF.com | 2020 | Kontakt | Suche |