|
|
Número de pieza | OB2278 | |
Descripción | Current Mode PWM Controller | |
Fabricantes | On-Bright | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de OB2278 (archivo pdf) en la parte inferior de esta página. Total 13 Páginas | ||
No Preview Available ! GENERAL DESCRIPTION
OB2278 is a highly integrated current mode PWM
control IC optimized for high performance, low
standby power and cost effective offline flyback
converter applications.
PWM switching frequency at normal operation is
externally programmable and trimmed to tight
range. At no load or light load condition, the IC
operates in extended ‘burst mode’ to minimize
switching loss. Lower standby power and higher
conversion efficiency is thus achieved.
VDD low startup current and low operating current
contribute to a reliable power on startup design
with OB2278. A large value resistor could thus be
used in the startup circuit for reduced power loss.
The internal slope compensation improves system
large signal stability and reduces the possible
sub-harmonic oscillation at high PWM duty cycle
output. Leading-edge blanking on current sense
input removes the signal glitch due to snubber
circuit diode reverse recovery and greatly reduces
the external component count and system cost in
the design.
OB2278 offers comprehensive protection
coverage including Cycle-by-Cycle current
limiting(OCP),
VDD
Under
Voltage
Lockout(UVLO),
VDD
Over
Voltage
Protection(OVP), VDD Clamp, Gate Clamp, Over
Load protection(OLP) and Over Temperature
protection (OTP), etc.
Different latch shutdown options are offered on
OB2278 in different device version. T version
supports both OVP and OTP latch shutdown. L
version provides all OVP, OTP and OLP latch
shutdown control.
Excellent EMI performance is achieved with soft
switching control at the totem pole gate drive
output.
OB2278 is offered in SOP-8 and DIP-8 packages.
TYPICAL APPLICATION
OB2278
Current Mode PWM ControllerLatch Shutdown
Product Specification
FEATURES
■ Power On Soft Start
■ Extended Burst Mode Control For Improved
Efficiency and Minimum Standby Power
Design
■ Audio Noise Free Operation
■ External Programmable PWM Switching
Frequency
■ Internal Synchronized Slope Compensation
■ Low VIN/VDD Startup Current(3uA) and Low
Operating Current (2.3mA)
■ Leading Edge Blanking on Current Sense
Input
■ Complete Protection Coverage with selective
protections for Latch Shutdown
o VDD Over Voltage Protection(OVP) – Latch
Shutdown
o Over Temperature Protection(OTP) – Latch
Shutdown
o Over Load Protection. (OLP) – Auto
recovery or Latch Shutdown
o VDD Under Voltage Lockout with Hysteresis
(UVLO)
o Gate Output Voltage Clamp (16.5V)
o Built-in OCP Compensation to Achieve
Minimum OPP Variation over Universal AC
Input Range.
APPLICATIONS
Offline AC/DC flyback converter for
■ Adaptor
■ Notebook Adaptor
■ LCD Monitor/TV/PC/Set-Top Box Power
Supplies
■ Open-frame SMPS
■ Printer Power
©On-Bright Electronics
Confidential
-1-
Datasheet
OB_DOC_DS_2278A2
1 page OB2278
Current Mode PWM ControllerLatch Shutdown
ELECTRICAL CHARACTERISTICS
(TA = 25℃, RI=100K ohm, VDD=16V, if not otherwise noted)
Symbol
Parameter
Test Conditions
Min Typ Max Unit
Supply Voltage (VDD)
I_VDD_Startup VDD Start up Current
VDD =15V Measure
current into VDD
3 20 uA
I_VDD_Ops
UVLO(Enter)
UVLO(Exit)
Operation Current
VDD Under Voltage
Lockout Enter
VDD Under Voltage
Lockout Exit (Startup)
VFB=3V
2.3 mA
8.8 9.8 10.8 V
15.5 16.5 17.5 V
OVP(Latch)
OVP(De-Latch)
VDD Over Voltage Latch
Trigger
VDD Latch Release
Voltage Threshold
26.5 28
7.5
29.5 V
V
I(Vdd)_latch
VDD bleeding current at
latch shutdown when VDD
= 9V
45 uA
TD_OVP
VDD_Clamp
T_Softstart
VDD OVP Debounce time
VDD Zener Clamp Voltage
Soft Start Time
I(VDD ) = 5 mA
80 uSec
35 V
3 mSec
Feedback Input Section(FB Pin)
AVCS
PWM Input Gain
VFB_Open
VFB Open Voltage
ΔVFB /ΔVcs
2.8 V/V
6.2 V
IFB_Short
FB pin short circuit current
Short FB pin to GND,
measure current
0.75
mA
VTH_0D
Zero Duty Cycle FB
Threshold Voltage
0.95 V
VTH_BM
Burst Mode FB Threshold
Voltage
1.6 V
VTH_PL
Power Limiting
Threshold Voltage
FB
4.4 V
TD_PL
Power limiting Debounce
Time
80 mSec
ZFB_IN
Input Impedance
9.0 Kohm
Current Sense Input(Sense Pin)
T_blanking
Sense Input Leading Edge
Blanking Time
300 nSec
ZSENSE_IN
TD_OC
Sense Input Impedance
Over Current Detection
and Control Delay
CL=1nf at GATE,
30 Kohm
70 nSec
Current Limiting Threshold
VTH_OC_0
at No Compensation
I(VIN) = 0uA
0.85 0.90 0.95 V
VTH_OC_1
Oscillator
FOSC
∆f_Temp
∆f_VDD
Current Limiting Threshold
at Compensation
I(VIN) = 150uA
Normal
Frequency
Frequency
Stability
Frequency
Stability
Oscillation
Temperature
Voltage
-20℃ to 100 ℃
VDD = 12-28V,
0.80 V
60 65 70 KHZ
3%
3%
©On-Bright Electronics
Confidential
-5-
Datasheet
OB_DOC_DS_2278A2
5 Page PACKAGE MECHANICAL DATA
8-Pin Plastic DIP
OB2278
Current Mode PWM ControllerLatch Shutdown
Symbol
A
A1
A2
B
B1
C
D
E
E1
e
L
E2
Dimensions In Millimeters
Min
3.710
Max
5.334
0.381
2.921
4.953
0.350
0.650
1.524 (BSC)
0.200
0.360
9.000
10.160
6.096
7.112
7.320
8.255
2.540 (BSC)
2.921
3.810
7.620
10.920
Dimensions In Inches
Min
0.146
Max
0.210
0.015
0.115
0.195
0.014
0.026
0.06 (BSC)
0.008
0.014
0.354
0.400
0.240
0.280
0.288
0.325
0.1 (BSC)
0.115
0.150
0.300
0.430
©On-Bright Electronics
Confidential
- 11 -
Datasheet
OB_DOC_DS_2278A2
11 Page |
Páginas | Total 13 Páginas | |
PDF Descargar | [ Datasheet OB2278.PDF ] |
Número de pieza | Descripción | Fabricantes |
OB2273 | High Performance Current Mode PWM Controller | On-Bright |
OB2273A | High Performance Current Mode PWM Controller | On-Bright |
OB2276 | High Performance Current Mode PWM Controller | On-Bright |
OB2276A | High Performance Current Mode PWM Controller | On-Bright Electronics |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |