|
|
PDF 269 Data sheet ( Hoja de datos )
| Número de pieza | 269 | |
| Descripción | 269-Type1480nmPumpLaserModule | |
| Fabricantes | AgereSystems | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de 269 (archivo pdf) en la parte inferior de esta página. Total 8 Páginas | ||
|
No Preview Available !
Data Sheet
June 2001
269-Type 1480 nm Pump Laser Module
Applications
s Erbium-doped fiber amplifiers (EDFA)
Description
The 269-type pump laser module is designed as a continuous-
wave (CW) optical pump source for erbium-doped fiber ampli-
fiers.
Features
s High-coupled rated output power up to 280 mW,
CW
s Wide environmental range
s Field-proven packaging technology
s InGaAsP/InP high-power, strained multiple quan-
tum-well (MQW) chip design
s Internal optical isolator (optional)
s Internal thermoelectric cooler (TEC)
s InGaAs PIN photodetector back-facet monitor
s Single-mode and polarization-maintaining fiber pig-
tails
s Compact, 14-pin butterfly package
s Industry compatible package and pinout
The 269-type pump laser module represents a family
of thermoelectrically cooled, high-power lasers. They
are designed as continuous-wave (CW) optical pump
sources for dense wavelength-division multiplexing
(DWDM) EDFA applications.
The laser modules incorporate a high-power, quan-
tum-well laser chip that achieves fiber powers up to
280 mW.
An integral thermoelectric cooler (TEC) stabilizes the
laser at room temperature and, combined with a her-
metic environment, allows the device to achieve
high-power operation over the extended temperature
range of 0 °C to 75 °C. An internal InGaAs PIN pho-
todiode, mounted behind the laser diode, functions
as the laser detector and monitors light emissions
from the rear facet of the laser.
The 269-type module is offered in a 14-pin, hermetic
butterfly package.
1 page  
Data Sheet
June 2001
User Information
Table 4. Pin Information
Pin
Number
Connection
1 TE Cooler (+)*
2 Thermistor
3 Monitor Anode (–Bias)
4 Monitor Cathode (+Bias)
5 Thermistor
6 No Connect
7 No Connect
8 No Connect
9 No Connect
10 Laser Anode (+)
11 Laser Cathode (–)
12 No Connect
13 Package Ground
14 TEC Cooler (–)
* A positive input into this pin cools the laser.
Fiber Characteristics
s Length of fiber pigtail:
— 1.75 m ± 0.25 m
s Standard fiber:
— Cladding OD: 125 µm ± 2 µm
— Acrylate buffer OD: 250 µm ± 15 µm
— Cut off wavelength: <1320 nm
s Polarization-maintaining fiber:
— PANDA
— Cut off wavelength: <1400 nm
— Acrylate buffer: 400 µm
269-Type 1480 nm Pump Laser Module
Mounting and Connections
CAUTION: This device is susceptible to damage as
a result of electrostatic discharge.
Proper precautions should be taken
during both handling and testing.
The base of the laser module (see Outline Diagram)
should be maintained at or below 75 °C (maximum)
during operation. Interfaces between the laser module
base and heat sink must be clean, and the use of a
thermal filler may be necessary.
Mounting Instructions
The minimum fiber bend radius is 1.0 in.
To avoid degradation in performance, mount the mod-
ule on the board as follows:
1. Place the bottom flange of the module on a flat heat
sink at least 0.5 in. x 1.180 in. (12.7 mm x 30 mm)
in size. The surface finish of the heat sink should be
better than 32 µin. (0.8 µm), and the surface flat-
ness must be better than 0.001 in. (25.4 µm). Using
thermal conductive grease is optional; however,
thermal performance may be improved if conductive
grease is applied between the bottom flange and
the heat sink.
2. Mount four #2-56 screws with Fillister heads
(M2-3 mm) at the four screw hole locations (see
Outline Diagram). The Fillister head diameter must
not exceed 0.140 in. (3.55 mm). Do not apply more
than 1 in./lb. of torque to the screws.
Agere Systems Inc.
7 65 43 21
+–
TH 10 kΩ
ISOLATOR
(OPTIONAL)
TEC
+–
8 9 10 11 12 13 14
Figure 1. Circuit Schematic
1-675 (F).i
5
5 Page | ||
| Páginas | Total 8 Páginas | |
| PDF Descargar | [ Datasheet 269.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| 2600 | Bobbin Wound Surface Mount Inductors |  C&DTechnologies |
| 2606AD | NJM2606AD |  New Japan Radio |
| 2606B | Return-Path Photodiode Receiver Module | AgereSystems |
| 2609B | Broadband Photodiode Module | AgereSystems |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |