|
|
Número de pieza | STM6519 | |
Descripción | 4-pin Smart Reset | |
Fabricantes | STMicroelectronics | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de STM6519 (archivo pdf) en la parte inferior de esta página. Total 25 Páginas | ||
No Preview Available ! Features
■ Operating voltage range 2 V to 5.5 V
■ Low supply current 1 μA
■ Integrated test mode
■ Single Smart Reset™ push-button input with
fixed extended reset setup delay (tSRC) from
0.5 s to 10 s in 0.5 s steps (typ.), option with
internal input pull-up resistor
■ Push-button controlled reset pulse duration
– Option 1: fully push-button controlled, no
fixed or minimum pulse width guaranteed
– Option 2: defined output reset pulse
duration (tREC), factory-programmed
■ Single reset output
– Active-low or active-high
– Push-pull or open drain with optional
pull-up resistor
■ Fixed Smart Reset input logic voltage levels
■ Operating temperature: -40 °C to +85 °C
■ UDFN4 package 1.00 mm x 1.45 mm and
UDFN6 package 1.00 mm x 1.45 mm
■ ECOPACK®2 (RoHS compliant, Halogen-
Free)
Applications
■ Mobile phones, smartphones, PDAs
■ e-books
■ MP3 players
■ Games
■ Portable navigation devices
■ Any application that requires delayed reset
push-button response for improved system
stability
STM6519
4-pin Smart Reset™
Datasheet - production data
UDFN4 1.00 mm x 1.45 mm
UDFN6 1.00 mm x 1.45 mm
January 2013
This is information on a product in full production.
Doc ID 022111 Rev 6
1/25
www.st.com
1
http://www.Datasheet4U.com
1 page STM6519
1 Descri
ption
Description
The Smart ResetTM devices provide a useful feature which ensures that inadvertent short
reset push-button closures do not cause system resets. This is done by implementing an
extended Smart Reset input delay time (tSRC), which ensures a safe reset and eliminates
the need for a specific dedicated reset button.
This reset configuration provides versatility and allows the application to distinguish between
a software generated interrupt and a hard system reset. When the input push-button is
connected to the microcontroller interrupt input, and is closed for a short time, the processor
can only be interrupted. If the system still does not respond properly, continuing to keep the
push-buttons closed for the extended setup time tSRC causes a hard reset of the processor
through the reset output.
The STM6519 has one Smart Reset input (SR) with preset delayed Smart Reset setup time
(tSRC). The reset output (RST) is asserted after the Smart Reset input is held active for the
selected tSRC delay time. The RST output remains asserted either until the SR input goes to
inactive logic level (i.e. neither fixed nor minimum reset pulse width is set) or the output reset
pulse duration is fixed for tREC (i.e. factory-programmed). The device fully operates over
a broad VCC range from 2.0 V to 5.5 V.
1.1 T
est mode
After pulling SR up to VTEST (VCC + 1.4 V) or above, the counter starts to count the initial
shortened tSRC-INI (42 ms, typ.). After tSRC-INI expires, the RST output either goes down for
tREC (if tREC option is used) or stays low as long as overvoltage on SR is detected (if tREC
option is not used). This is feedback, and the user only knows that the device is locked in
test mode. Each time the SR input is connected to ground in test mode, a shortened
tSRC-SHORT (tSRC/128) is used instead of regular tSRC (0.5 s - 10 s). In this way the device
can be quickly tested without repeating test mode triggering. Return to normal mode is
possible by performing a new startup of the device (i.e. VCC goes to 0 V and back to its
original state).
The advantages of this solution are its high glitch immunity, user feedback regarding entry
into test mode, and testability within the full VCC range.
Doc ID 022111 Rev 6
5/25
5 Page STM6519
5 T iming diagrams
Figure 8. RST output without tREC option
Timing diagrams
1. VCC should be powered up before or together with voltage on the SR input to prevent entering test mode by creating
a condition V(SR) > VCC +1.1 V typ.
Figure 9. RST output with tREC option
1. VCC should be powered up before or together with voltage on the SR input to prevent entering test mode by creating
a condition V(SR) > VCC +1.1 V typ.
Doc ID 022111 Rev 6
11/25
11 Page |
Páginas | Total 25 Páginas | |
PDF Descargar | [ Datasheet STM6519.PDF ] |
Número de pieza | Descripción | Fabricantes |
STM6510 | Dual push-button Smart Reset | STMicroelectronics |
STM6513 | Microprocessor Supervisors And Reset ICs | ST Microelectronics |
STM6519 | 4-pin Smart Reset | STMicroelectronics |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |