|
|
PDF APL5155 Data sheet ( Hoja de datos )
| Número de pieza | APL5155 | |
| Descripción | 150mA LDO Regulator | |
| Fabricantes | Anpec Electronics | |
| Logotipo |  |
|
1. APL5155  Hay una vista previa y un enlace de descarga de APL5155 (archivo pdf) en la parte inferior de esta página. Total 20 Páginas | ||
|
No Preview Available !
APL5155
High Input Voltage, Low Quiescent Current, 150mA LDO Regulator
Features
General Description
• Wide Input Voltage Range: 5.4V to 25V
The APL5155 is a low ground current linear regulator,
• Ultra Low Ground Current: 10µA
which operates with input voltage from 5.4V to 25V and
• High Output Accuracy: ±2.5%
delivers output current up to 150mA. Typical dropout volt-
• Excellent Load/Line Transient
age is only 750mV at 150mA loading. This combination
• Low Dropout Voltage: 750mV @ 150mA
of the high voltage and the low ground current makes the
APL5155 ideal for USB and portable devices, using 2-
•
Fixed Output Voltages for 5V/3.3V or Adjustable
cell or 3-cell Li-Ion battery inputs.
Voltage
The APL5155 is stable with aluminum, tantalum, and
• Built-In Current-Limit Protection
ceramic capacitors. It requires a 1µF or greater capacitor
• Built-In Over-Temperature Protection
for stability.
• Zero Shutdown Current
The APL5155 has many protection functions, including
• Internal Soft-Start Function
over-temperature, current-limit and short circuit current
• POR Scheme to Prevent VOUT Spike
limit protections, which prevent the device from thermal
• SOT-23-5, SOT-89, and SOP-8P Packages
• Lead Free and Green Devices Available
(RoHS Compliant)
over-load and current over-load.
The APL5155 regulator is available in miniature SO T-23-
5, SOT-89, and SOP-8P packages.
Applications
Pin Configuration
• USB Power Supply
• Keep-Alive Supply in Notebook and Portable
Computers
• Logic Supply for High-Voltage Batteries
• Battery Powered Systems
VIN 1
GND 2
EN 3
5 VOUT
4 NC/ADJ
SOT-23-5
(Top View)
GND 1
VIN 2
TAB : VIN
VOUT 3
SOT-89
(Top View)
VOUT 1
NC 2
NC 3
NC/ADJ 4
SOP-8P
(Top View)
8 VIN
7 GND
6 NC
5 EN
= Thermal Pad
(connected to GND plane for better heat dissipation)
ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and
advise customers to obtain the latest version of relevant information to verify before placing orders.
Copyright © ANPEC Electronics Corp.
Rev. A.3 - Sep., 2012
1
www.anpec.com.tw
http://www.Datasheet4U.com
1 page  
APL5155
Typical Operating Characteristics
Quiescent Current vs. Input Voltage
12
No Load
11
10
9
8
7
6
0 2 4 6 8 10 12 14 16 18 20 22 24 26
Input Votlage (V)
Quiescent Current vs. Junction Temperature
14
VIN =8V, No Load
12
10
8
6
4
2
0
-40 -20 0 20 40 60 80 100 120
Junction Temperature (oC)
Reference Voltage vs. Junction Temperature
1.260
1.255
VIN =8V
1.250
1.245
1.240
1.235
1.230
1.225
1.220
-40 -20 0 20 40 60 80 100 120
Junction Temperature (oC)
Copyright © ANPEC Electronics Corp.
Rev. A.3 - Sep., 2012
5
Quiescent Current vs. Output Current
300
VIN =12V
250
200
150
100
50
0
0 25 50 75 100 125 150
Output Current (mA)
Dropout Voltage vs. Output Current
1.0
0.9 VOUT=20V
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
0 25 50 75 100 125
Output Current (mA)
150
PSRR vs. Frequency
0
-10
VIN=12V, VIN=3.3V,
CIN=1µF, COUT=2.2µF
-20
-30
-40
-50
-60
-70
-80
-90
-100
0.1
1 10 100
Frequency (kHz)
1000
www.anpec.com.tw
5 Page 
APL5155
Application Information
Enable/Shutdown
The APL5155 features an active-high enable pin that al-
lows the regulator to be disabled. Forcing the enable pin
low disables the regulator, so current consumed by the
regulator goes nearly to zero. Forcing the enable pin high
enables the output voltage. The enable pin can not float.
Input Capacitor
The APL5155 has high input voltage up to 25V. The input
capacitor must be rated to sustain voltages that may be
used on the input. An input capacitor may be required
when the device is not near the source power supply or
when supplied by a battery. Small and surface-mounted
ceramic capacitors can be used for bypassing. A larger
value may be required if the source supply has high ripple.
PD(MAX)
=
TJ − TA
θJA
where T -T is the temperature difference between the
JA
junction and ambient air. θJA is the thermal resistance
between junction and ambient air.
For continual operation, do not exceed the absolute maxi-
mum junction temperature rating of TJ=125oC.
For example:
In SOT-23-5 package θJA=235oC/W. When operates the
APL5155 at TA=50oC, the maximum power dissipation
can be determined as below:
P =(125oC-50oC)/(235oC/W)
D(MAX)
P =319.1mW
D(MAX)
Thermal Pad Consideration
Output Capacitor
The APL5155 requires an output capacitor for stabilit y.
The design requires 1µF or greater on the output to main-
tain stability. It is optimized by using low-ESR ceramic
chip capacitors. The maximum allowable ESR is 3Ω. More
capacitance improves transient response. Place the out-
put capacitor as close to the VOUT pin as possible.
X7R/X5R dielectric-type ceramic capacitors are recom-
mended because of their temperature performance. X7R
type capacitors change capacitance by 15% over their
operating temperature ranges. To use a ceramic chip
capacitor with Y5V dielectric, the value must be much
higher than an X7R ceramic capacitor to ensure the same
minimum capacitance over the equivalent operating tem-
perature range.
The SOP-8P is a cost-effective package which features a
small size, like a standard SOP-8, and a bottom thermal
pad to minimize the thermal resistance of the package is
applicable to high current applications. The thermal pad
must be soldered down to the copper plane on circuit
board. Heat can be conducted away from the thermal
pad through the copper plane to ambient. If the copper
plane is not on the top surface of the circuit board, 4 or 6
vias should be used to thermally couple the thermal pad
to the bottom plane.
For good thermal conduction, the vias must be plated
through and solder filled. The copper plane used to con-
duct heat away from the thermal pad should be as large
as practical.
0.072
0.118
No-Load Stability
The APL5155 will remain stable and in regulation with no
load unlike many other voltage regulators. This is espe-
cially important in CMOS RAM keep-alive applications.
0.150
0.024
Thermal Consideration
The thermal resistance of junction to ambient controls
the APL5155's maximum power dissipation. The power
dissipation across the device is PD=IOUT (VIN-VOUT), and the
maximum power dissipation is:
0.212
SOP-8P Layout Recommendation
ground
plane for
thermal
pad
Copyright © ANPEC Electronics Corp.
Rev. A.3 - Sep., 2012
11
www.anpec.com.tw
11 Page | ||
| Páginas | Total 20 Páginas | |
| PDF Descargar | [ Datasheet APL5155.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| APL5151 | (APL5151 - APL5154) Low Dropout 150mA Fixed Voltage Regulator | Anpec Electronics |
| APL5152 | (APL5151 - APL5154) Low Dropout 150mA Fixed Voltage Regulator | Anpec Electronics |
| APL5153 | (APL5151 - APL5154) Low Dropout 150mA Fixed Voltage Regulator | Anpec Electronics |
| APL5154 | (APL5151 - APL5154) Low Dropout 150mA Fixed Voltage Regulator | Anpec Electronics |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |