Datenblatt-pdf.com


UB2016 Schematic ( PDF Datasheet ) - Unisonic Technologies

Teilenummer UB2016
Beschreibung ONE-CELL STANDALONE LINEAR LITHIUM BATTERY CHARGER
Hersteller Unisonic Technologies
Logo Unisonic Technologies Logo 




Gesamt 13 Seiten
UB2016 Datasheet, Funktion
UNISONIC TECHNOLOGIES CO., LTD
UB2016
Preliminary
ONE-CELL STANDALONE
LINEAR LITHIUM BATTERY
CHARGER
CMOS IC
„ DESCRIPTION
UTC UB2016 is a complete, constant current and constant voltage
linear charger for single cell lithium-ion batteries. Its small size and
ability to regulate low charge currents make UTC UB2016 especially
well-suited for portable applications using low capacity rechargeable
lithium-ion coin cells. Furthermore, UTC UB2016 is specifically
designed to work within USB power specifications.
No external sense resistor is needed, and no blocking diode is
required due to the internal MOSFET architecture. The charge
voltage is fixed at 4.2V, and the charge current can be programmed
externally with a single resistor. UTC UB2016 automatically
terminates a charge cycle when the charge current drops to 1/10th
the programmed value after the final float voltage is reached.
„ FEATURES
* Programmable Charge Current Up to 500mA.
* No External MOSFET, Sense Resistor or Blocking Diode Required.
* Complete linear charger in ThinSOT Package for Single Cell / Coin Cell Lithium-lon Batteries.
* Constant Current / Constant Voltage Operation with Thermal Regulation to Maximize Charge Rate Without Risk
of Overheating.
* Charges Single Cell Li-lon Batteries Directly form USB Port.
* Preset 4.2V Charge Voltage with High Accuracy about ±1.2%.
* Automatic Recharge.
* 2.9V Trickle Charge Threshold.
* 20µA Supply Current in Shutdown Mode.
* Charge Status Output Pin.
„ ORDERING INFORMATION
Ordering Number
Lead Free
Halogen Free
UB2016L-xx-AF5-R
UB2016G-xx-AF5-R
Note: xx: Output Voltage, refer to Marking Information.
Package
SOT-25
Packing
Tape Reel
UB2016G-xx-AF5-R
(1)Packing Type
(2)Package Type
(3)Output Voltage Code
(4)Halogen Free
(1) R: Tape Reel
(2) AF5: SOT-25
(3) xx: Refer to Marking Information
(4) G: Halogen Free, L: Lead Free
www.unisonic.com.tw
Copyright © 2012 Unisonic Technologies Co., Ltd
1 of 13
QW-R502-869.a
Free Datasheet http://www.Datasheet4U.com






UB2016 Datasheet, Funktion
UB2016
Preliminary
CMOS IC
„ OPERATION
The UTC UB2016 is a single cell lithium-ion battery charger using a constant-current/constant-voltage algorithm. It
can deliver up to 500mA of charge current (using a good thermal PCB layout) with a final float voltage accuracy of
±1.2%. The UTC UB2016 includes an internal P-channel power MOSFET and thermal regulation circuitry. No
blocking diode or external current sense resistor is required; thus, the basic charger circuit requires only two external
components. Furthermore, the UTC UB2016 is capable of operating from a USB power source.
1. Normal Charge Cycle
A charge cycle begins when the voltage at the VCC pin rises above the UVLO threshold level and a 1% program
resistor is connected from the PROG pin to ground or when a battery is connected to the charger output. If the BAT
pin is less than 2.9V, the charger enters trickle charge mode. In this mode, the UTC UB2016 supplies approximately
1/10 the programmed charge current to bring the battery voltage up to a safe level for full current charging. When the
BAT pin voltage rises above 2.9V, the charger enters constant-current mode, where the programmed charge current
is supplied to the battery. When the BAT pin approaches the final float voltage (4.2V), the UTC UB2016 enters
constant-voltage mode and the charge current begins to decrease. The charge cycle ends when the charge current
drops to 1/10 of the programmed value.
2. Programming Charge Current
The charge current is programmed using a single resistor from the PROG pin to ground. The battery charge
current is 1100 times the current out of the PROG pin. The program resistor and the charge current are calculated
using the following equations:
RPROG
=
1000V
ICHG
,
ICHG
=
1000V
RPROG
The charge current out of the BAT pin can be determined at any time by monitoring the PROG pin voltage using the
following equation:
IBAT
=
VPROG
RPROG
× 1000
This actual current will vary from IC to IC. The typical variation is within ±20%.
3. Charge Termination
A charge cycle is terminated when the charge current falls to 1/10th the programmed value after the final float
voltage is reached. This condition is detected by using an internal, filtered comparator to monitor the PROG pin.
When the PROG pin voltage falls below 100mV for longer than tTERM (typically 1ms), charging is terminated. The
charge current is latched off and the UTC UB2016 enters standby mode, where the input supply current drops to
200mA. (Note: C/10 termination is disabled in trickle charging and thermal limiting modes).
When charging, transient loads on the BAT pin can cause the PROG pin to fall below 100mV for short periods of
time before the DC charge current has dropped to 1/10th the programmed value. The 1ms filter time (tTERM) on the
termination comparator ensures that transient loads of this nature do not result in premature charge cycle
termination. Once the average charge current drops below 1/10th the programmed value, the UTC UB2016
terminates the charge cycle and ceases to provide any current through the BAT pin. In this state, all loads on the
BAT pin must be supplied by the battery. The UTC UB2016 constantly monitors the BAT pin voltage in standby
mode. If this voltage drops below the 4.1V recharge threshold (VRECHRG), another charge cycle begins and current is
once again supplied to the battery. To manually restart a charge cycle in standby mode, the input voltage must be
removed and reapplied, or the charger must be shut down and restarted using the PROG pin.
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
6 of 13
QW-R502-869.a
Free Datasheet http://www.Datasheet4U.com

6 Page









UB2016 pdf, datenblatt
UB2016
Preliminary
„ TYPICAL APPLICATION CIRCUIT
5V WALL
ADAPTER
500mA ICHG
USB POWER
400mA ICHG MP1
BAT
D1 UTC
UB2016
VCC
1µF
1kΩ
PROG
GND
CMOS IC
IBAT
+ Li-Ion
BATTERY
2.5kΩ
10kΩ MN1
100mA/
500mA
µC
Fig. 1 USB/Wall Adapter Power Li-Ion Charger
330Ω
5V
LED
VCC
BAT
UTC
UB2016
CHRG
PROG
GND
1µF
2kΩ
+ Li-Ion
BATTERY
MN1 SHDN
Fig. 2 Full Featured Single Cell Li-Ion Charger
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
12 of 13
QW-R502-869.a
Free Datasheet http://www.Datasheet4U.com

12 Page





SeitenGesamt 13 Seiten
PDF Download[ UB2016 Schematic.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
UB2012ADVANCED LINEAR CHARGE MANAGEMENT ICUnisonic Technologies
Unisonic Technologies
UB2016ONE-CELL STANDALONE LINEAR LITHIUM BATTERY CHARGERUnisonic Technologies
Unisonic Technologies
UB2017ONE-CELL STANDALONE LINEAR LITHIUM BATTERY CHARGERUnisonic Technologies
Unisonic Technologies

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com       |      2020       |      Kontakt     |      Suche