|
|
PDF T215HVN01.0 Data sheet ( Hoja de datos )
| Número de pieza | T215HVN01.0 | |
| Descripción | TFT LCD Module | |
| Fabricantes | AUO | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de T215HVN01.0 (archivo pdf) en la parte inferior de esta página. Total 32 Páginas | ||
|
No Preview Available !
Product Specification
AU OPTRONICS CORPORATION
T215HVN01.0
( V ) Preliminary Specification
( ) Final Specification
Module
Model Name
21.5” Color TFT-LCD
T215HVN01.0
Customer
Date
Approved by
Date
Howard Lee
Approved by
Prepared by
Eugene Hsu
2012/08/01
Note: This Specification is subject to change
without notice.
AU Optronics Corporation
document version 0.3
1
Free Datasheet http://www.Datasheet4U.com
1 page  
Product Specification
AU OPTRONICS CORPORATION
1 Handling Precautions
T215HVN01.0
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth
when handling.
7) Do not open or modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a Module has to be put back into the packing container slot after once it was taken out
from the container, do not press the center of LED light bar edge. Instead, press at the far ends
of the LED light bar edge softly. Otherwise the TFT Module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the
Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure, do not twist nor bend the TFT Module
even momentary. At designing the enclosure, it should be taken into consideration that no
bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT Module
may be damaged.
12) Small amount of materials having no flammability grade is used in the LCD module. The LCD
module should be supplied by power complied with requirements of Limited Power Source
(IEC60950 or UL1950), or be applied exemption.
13) Avoid touching COF position while doing mechanical design.
14) While storing modules as spares for a long time, the following precautions are necessary:
Store modules in a dark place. Do not expose them to sunlight or fluorescent light.
Keep the temperature between 5°C and 35°C at normal humidity.
document version 0.3
5
Free Datasheet http://www.Datasheet4U.com
5 Page 
Product Specification
AU OPTRONICS CORPORATION
T215HVN01.0
3 Functional Block Diagram
The following diagram shows the functional block of the 21.5 inch Color TFT-LCD Module:
LVDS
+5V
AUO
ASIC
LVDS
Receiver
Timing
Controller
miniLVDS
Transmitter
DC/DC
Converter
Gamma
Correction
G1
TFT-LCD
1920(x3) x 1080
Pixels
G1080
D1
X-Driver IC
D5760
LED
Backlight
I/F + X-PCB
DC
LED Driver on system
I/F PCB Interface:
MSCKT2407P30HB
AL230F-A0G1D-P
Mating Type:
FI-X30HL(Locked Type) (TBD)
document version 0.3
11
Free Datasheet http://www.Datasheet4U.com
11 Page | ||
| Páginas | Total 32 Páginas | |
| PDF Descargar | [ Datasheet T215HVN01.0.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| T215HVN01.0 | TFT LCD Module | AUO |
| T215HVN01.2 | Color TFT-LCD | AUO |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |