|
|
Número de pieza | 216WA01 | |
Descripción | TFT LCD Module | |
Fabricantes | Chunghwa Picture Tubes | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de 216WA01 (archivo pdf) en la parte inferior de esta página. Total 26 Páginas | ||
No Preview Available ! Chunghwa Picture Tubes, Ltd.
Technical Specification
To : AMCOM
Date : 2008.12.03
CPT TFT-LCD
CLAA 216WA01
ACCEPTED BY:
APPROVED BY
康豊鑫
CHECKED BY
溫文良
PREPARED BY
Product Planning
Management
General Division
Prepared by: Design General Division
CHUNGHWA PICTUER TUBES, LTD.
No. 1, Huaying Rd., Sanho Tsun, Lungtan Shiang, Taoyuan, Taiwan, 325, R.O.C.
TEL: +886-3-4805678 FAX: +886-3-4800589
Doc. No: CLAA216WA01-AMCOM-SPEC-20081203 Issue Date: 2008/12/03
Free Datasheet http://www.datasheetlist.com/
1 page Title:CLAA216WA01
CHUNGHWA PICTUER TUBES, LTD.
TECHNICAL SPECIFICATION
Technical Specification
Doc. No:
Version:
Issue Date :
A
2008/11/25
2. ABSOLUTE MAXIMUM RATINGS
ITEM
SYMBOL MIN. MAX.
UNIT REMARK
Power Supply Voltage for LCD VCC
0
6
V
Lamp Voltage
Delta
STI
VL
VL
780
760
930
950
Vrms
Lamp Current
Delta
STI
ILO 3
ILO 3
8
8
mArms
Lamp Frequency
static electricity
FL
VESDt
VESDc
40
-200
-8000
80
200
8000
kHz
V
V
*5)
Operation Temperature Top 0 50 ℃ *1). 2). 3). 6)
Storage Temperature
Tstg -20
60
℃ *1). 2). 3)
Delayed Discharge Time
TD
--
1
sec *8)
[Note]
1).The relative temperature and humidity range are as below sketch, 90%RHMax.(Ta≦40℃).
2).The maximum wet bulb temperature ≦39℃(Ta>40℃) and without dewing.
3).If you use the product in an environment which over the definition of temperature and humidity too
long to effect the result of eye-etching.
4).The life time of the lamp is related to the current of the lamp, so please according to the description
of the “(b) backlight” on page 7.
5).Test Condition: IEC 1000-4-2 VESDt: Contact discharge to input connector; VESDC: Contact
discharge to module
6).If you operate the product in normal temperature range, the center surface of panel should be under
50℃.
7).When lamp current is out of the absolute maximum range, the life will fall rapidly or shown
unusual sign.
IL min 2mA only for test only, but we can’t guarantee the lifetime and performance.
8).Delay lighting testing needs the volt above start voltage Vrms. Before the procedure tube needs
typical lighting for 1 minute and stay in the temperature 25±2℃ for 24 hours and then testing in the
same condition in dark room.
ISO Datasheet No:
Datasheet Version.: 01
CHUNGHWA PICTUER TUBES, LTD.
Page: 5/26
Free Datasheet http://www.datasheetlist.com/
5 Page Title:CLAA216WA01
CHUNGHWA PICTUER TUBES, LTD.
TECHNICAL SPECIFICATION
Technical Specification
Doc. No:
Version:
Issue Date :
A
2008/11/25
inverter and module to avoid the interference.
5) Definition of the lamp life time:
a. Luminance (L) under 50% of specification.
b. Starting Lamp Voltage: over130% of the initial value. Ta=25℃
6) The condition of Turn-on and Turn-off operation is as below:
a. Lamp current is 7.5mA
b. Frequency is 10 sec.(on)/10 sec.(off)
c. Repeat it for 100 thousand times
d. The lamp hue variation must smaller than 0.03
e. It should not have motion fail when starting lamp voltage is lower than 130%of the initial
value.
7) For keeping good lighting situation, when design the inverter, it must be considered that the
voltage large than starting lamp voltage.
8) WL=IL x VL x 4。(IL=7.5mA,Ta=25℃)
9) The Starting Lamp Voltage (VS) of inverter must be driven large than one second.
10) The output voltage of inverter (Vn) must be the same phase of between any lamps.
11) The difference in voltage between any lamps (△V) must be smaller than 300V at the same time.
Example:∣△V∣<300V,△V: = V1(t)-V2(t)
Vnrms − VL ≤ 15%
12) VL
,n=1,2… 4,n:the number of lamp
△V
V1(t)
V2(t)
13) The lamp working current (Icyc) of any cycle of lighting driving wave can’t exceed maximum of
lamp standard working current (IL).Therefore, the inverter design should be avoided the state.
ISO Datasheet No:
Datasheet Version.: 01
CHUNGHWA PICTUER TUBES, LTD.
Page: 11/26
Free Datasheet http://www.datasheetlist.com/
11 Page |
Páginas | Total 26 Páginas | |
PDF Descargar | [ Datasheet 216WA01.PDF ] |
Número de pieza | Descripción | Fabricantes |
216WA01 | TFT LCD Module | Chunghwa Picture Tubes |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |