|
|
Número de pieza | 58LT00F | |
Descripción | TA58LT00F | |
Fabricantes | Toshiba Semiconductor | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de 58LT00F (archivo pdf) en la parte inferior de esta página. Total 10 Páginas | ||
No Preview Available ! TOSHIBA Bipolar Linear Integrated Circuit Silicon Monolithic
TA58LT00F
TA58LT00F
150 mA Output Current and Tracking Regulator with ON/OFF Control Switch
The TA58LT00F consists of small-surface mount type tracking
regulators with an output current of 150 mA (maximum) and an
ON/OFF control switch. Control by an EN (ON/OFF) terminal
enables the regulator to be operated only when required (output ON).
The output voltage can be controlled to an arbitrary voltage between
2.5V and 13.4V by applying a necessary voltage to ADJ through a
microcontroller, etc. It is also possible to enable or disable the
regulator via the enable (ON/OFF) terminal. Enabling the regulator
only when necessary contributes to the energy saving of equipment.
Features
HSIP5-P-1.27B
• Built-in ON/OFF control function (active high)
Weight : 0.36 g (Typ.)
• Maximum output current : 150mA
• Output voltage
: 2.5 V ∼ 13.4 V
• Tracking voltage accuracy : ± 10mV (@Tj = 25°C)
• Low standby current (output OFF mode) : 1μA (Typ.)
• Protection function
: Over-current protection / thermal shutdown /
Reverse connection of power supply / 60 V load dump
• Package type
: Surface-mount New PW-Mold5pin
Pin Assignment
Mark
12345
IN EN GND ADJ OUT
Marking
3
58LT00F
12345
Part No. (or abbreviation code)
Lot No.
A line indicates
lead (Pb) - free package or
lead (Pb) - free finish.
1 2006-11-06
Free Datasheet http://www.Datasheet-PDF.com/
1 page TA58LT00F
Electrical Characteristics Common to All Products
• Tj = 25°C in the measurement conditions of each item is a regulation for where the standard condition
when a pulse test is carried out, and any drift in the electrical characteristic due to a rise in the junction
temperature of the chip may be disregarded.
Standard Application Circuit
Reg.IC.
CIN
0.33 μF
CPU etc.
IN OUT
TA58LT00F
ADJ EN
GND
COUT
10∼22 μF
ESR
0.5∼2Ω
Load
• Place CIN as close as possible to the input terminal and GND. Place COUT as close as possible to
the output terminal and GND. Although capacitor COUT acts to smooth the dc output voltage
during suspension of output oscillation or load change, it might cause output oscillation in a cold
environment due to increased capacitor ESR. It is therefore recommended to use a capacitor with
small temperature sensitivity. Please connect the resistance of 0.5∼ 2Ω with the series when the
ceramic capacitor is used.
The IC may oscillate due to external conditions (output current, temperature, or the type of the
capacitor used). The type of capacitor required must be determined by the actual application circuit
in which the IC is used.
The notice in case of application
• Note that, depending on the load conditions, a steep increase in the input voltage (VIN) may cause
a momentary rise in output voltage (VOUT) even if the EN (enable) pin is Low.
5 2006-11-06
Free Datasheet http://www.Datasheet-PDF.com/
5 Page |
Páginas | Total 10 Páginas | |
PDF Descargar | [ Datasheet 58LT00F.PDF ] |
Número de pieza | Descripción | Fabricantes |
58LT00F | TA58LT00F | Toshiba Semiconductor |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |