Datenblatt-pdf.com


OVC3860 Schematic ( PDF Datasheet ) - OmniVision

Teilenummer OVC3860
Beschreibung AT Command Application Notes
Hersteller OmniVision
Logo OmniVision Logo 




Gesamt 21 Seiten
OVC3860 Datasheet, Funktion
OVC3860 AT Command Application Notes
OVC3860
AT Command
Application Notes
Last Modified:2012-10-18
Document Revision:1.1
OmniVision Technologies, Inc. reserves the right to make changes without further notice to any product herein to improve
reliability, function or design. OmniVision does not assume any liability arising out of the application or use of any project,
circuit described herein; neither does it convey any license under its patent nor the right of others.
The datasheet is the official document of OmniVision. The applicaton notes are application guide lines for reference. If
there are any difference between datasheet and application notes, please follow datasheet and kindly report the
difference to OVT FAE.
This document contains information of a proprietary nature. None of this information shall be divulged to persons other
than OmniVision Technologies, Inc. employee authorized by the nature of their duties to receive such information, or
individuals or organizations authorized by OmniVision Technologies, Inc.
Company Confidential
1
Free Datasheet http://www.datasheet4u.com/






OVC3860 Datasheet, Funktion
OVC3860 AT Command Application Notes
AT Command
MG
MH
MI
MJ
MO
MP
MQ
MR
MS
MT
MV
MW
MX
MZ
ST
VC
VD
VE
VF
VG
VH
VI
VJ
VU
VX
Notion
Enable autoconn
Disble autoconn
Connect to av source
Disconnect from av source
Query avrcp status
Enable auto answer
Disable auto answer
Start FF
Start Rewind
Stop FF/Rewind
Query a2dp status
Write a byte to memory
Read a byte from memory
Switch two remote devices
SPP send data
Set clock debug mode
Decrease volume
Enter test mode
Set to a fixed frequency
Entering EMC test mode
Set RF reg
Start inquiry
Cancel inquiry
Increase volume
OOL power off
Response Indication
OK
OK
MB/MA
MY
ML<status>
OK
OK
OK
OK
OK
MU<status>
OK
MEM:<val>
SW
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
3.4. State Indications
In addition to the state indications mentioned above, there are some other indications used,
such as audio state indications. The following is the introdution of these state indications
State Indication
II
IJ2
IV
IA
IF
Description
In pairing state
Exit pairing state
Connected
Disconnected
Phone hand up
Company Confidential
6
Free Datasheet http://www.datasheet4u.com/

6 Page









OVC3860 pdf, datenblatt
OVC3860 AT Command Application Notes
#CE HFP Status = 4 IG
Pick up Indication
Description
This command causes the module to answer an incoming call. The information response and
causes will indicate the command success or failure.
Syntax: AT#CE
4.6. Reject Call #CF
Command Current Status(s) Possible
Indication Description
Indication(s)
#CF HFP Status = 4 IF
Hang up Indication
Description
This command causes the module to reject an incoming call. The information response and causes
will indicate the command success or failure.
Syntax: AT#CF
4.7. End Call #CG
Command Current Status(s) Possible
Indication Description
Indication(s)
#CG
HFP Status = 5 | IF
Hang up Indication
6
Description
This command causes the module to end an active call. The information response and causes will
indicate the command success or failure.
Syntax: AT#CG
4.8. Redial #CH
Command Current Status(s) Possible
Indication Description
Indication(s)
#CH
HFP Status = 3 | IC
Outgoing Call Indication
6
Description
This command causes the module to redial the last number called in the phone. The information
response and causes will indicate the command success or failure.
Syntax: AT#CH
4.9. Voice Dial #CI
Command Current Status(s) Possible
Indication Description
Indication(s)
#CI HFP Status = 3 PE
Voice Dial Start Indication
PF Handset Not Support Void Dial
Description
This command causes the module to active voice dial functionary in the phone. The information
response and causes will indicate the command success or failure.
Note: Voice dialing not works in some handset while .
Syntax: AT#CI
4.10. Cancel Voice Dial #CJ
Command Current Status(s) Possible
Indication(s)
Indication Description
Company Confidential
12
Free Datasheet http://www.datasheet4u.com/

12 Page





SeitenGesamt 21 Seiten
PDF Download[ OVC3860 Schematic.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
OVC3860AT Command Application NotesOmniVision
OmniVision
OVC3860Bluetooth 2.0 + EDR Stereo Audio ProcessorOmniVision
OmniVision
OVC3860Bluetooth ModuleYIGASN
YIGASN
OVC3860Bluetooth 2.0ETC
ETC

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com       |      2020       |      Kontakt     |      Suche