CS-800 Datasheet PDF - CONNECT SYSTEMS
| Part Number | CS-800 | |
| Description | Full Duplex Interconnect | |
| Manufacturers | CONNECT SYSTEMS | |
| Logo |  |
|
|
There is a preview and CS-800 download ( pdf file ) link at the bottom of this page. Total 32 Pages | ||
Preview 1 page No Preview Available !
CONNECT SYSTEMS INC.
1802 Eastman Ave. Suite 116
Ventura, Ca. 93003
Phone (805) 642-7184
Fax (805) 642-7271
Model CS-800
Full Duplex Interconnect
USER'S INSTRUCTION MANUAL
Revised 10/94
Made in U.S.A.
Copyright (C) 1991 By Connect Systems Inc.
Connect Systems Inc. - Model CS-800
Page 1
Free Datasheet http://www.datasheet4u.com/
|
| |
 
P4 STATUS TONES
P5 COS
P6 RPT AUDIO
P7 HYBRID BALANCE
Status beeps & CW ID level: Adjust for
desired modulation level of status beeps or
CW ID.
COS Threshold level: Measure the voltage at
TP-1 with no signal. Then measure the voltage
again with a signal applied. Adjust P-5 until
the voltage reading at TP-2 is approximately
midway between the two readings previously
obtained at TP-1.
For example: If TP-1 read 2 volts with no
signal, and 4 volts with a signal applied to
the receiver, TP-2 would be set to read
3 volts.
When JP-2 is correctly strapped and P5 is
properly adjusted, the RX LED will be
illuminated when there's a signal and go out
when the signal is removed.
Repeat Audio: Sets the modulation level of
repeat audio in repeater mode. Adjust only
after adjustment of P1 has been completed.
See discussion next page.
JUMPER STRAP OPTIONS
JP-1
De-emphasis strap. De-emphasizes the incoming audio (use when
taking audio directly from the FM detector). Cut JP-1 when
connecting to a source of flat audio such as the high side of
the volume control.
JP-2 COS polarity select strap. Strap in = non inverted. Remove
plastic clip for polarity inversion.
JP-3 Audio output range strap. Strap in = low level (0-1 V). Strap
cut = high level (0-5 V). Strap factory installed.
JP-4
Selects whether the Aux. Relay output is normally open (NO) or,
normally closed (NC). JP-5 is factory strapped for NO. For NC
operation, connect the center pad to the NC pad.
JP-5
Line in use detect strap. Must be installed if the 'line in
use' feature is to be used (See programming line 1.2.). Be sure
to program line 1.2. with a 0 (to disable) if JP-5 is not
strapped.
To enable line in use detect, simply slide the plastic clip off
one of the posts, and re-install over both posts. Be sure to
program line 1.2. with a '1'.
Connect Systems Inc. - Model CS-800
Page 5
Free Datasheet http://www.datasheet4u.com/
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for CS-800 electronic component. |
| Information | Total 32 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ CS-800.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| CS-800 | The function is Full Duplex Interconnect. CONNECT SYSTEMS | |
| CS-800 | The function is OPERATION MANUAL. ELTRA |  |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
CS-8
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||