|
|
PDF MF70 Data sheet ( Hoja de datos )
| Número de pieza | MF70 | |
| Descripción | Micro Milling Machine | |
| Fabricantes | PROXXON | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de MF70 (archivo pdf) en la parte inferior de esta página. Total 7 Páginas | ||
|
No Preview Available !
ProxxonTools.com
MF 70
1-3
4-6
71--130
4-6
7-10
5
3
0
5
4
3
5
3
0
5
4
3
5
5
5
5
5
4
5
5
5
5
4
3
12
Manual
Free Datasheet http://www.datasheet4u.com/
1 page  
GROUNDING INSTRUCTIONS:
1. All grounded, cord-connected tools:
In the event of a malfunction or breakdown, grounding
provides a path of least resistance for electric current to
reduce the risk of electric shock. This tool is equipped with
an electric cord having an equipment-grounding conductor
and a grounding plug. The plug must be plugged into a
matching outlet that is properly installed and grounded in
accordance with all local codes and ordinances. Do not
modify the plug provided -- if it will not fit the outlet, have
the proper outlet installed by a qualified electrician.
Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. The
conductor with insulation having an outer surface that is
green with or without yellow stripes is the equipment-
grounding conductor. If repair or replacement of the
electric cord or plug is necessary, do not connect the
equipment-grounding conductor to a live terminal. Check
with a qualified electrician or service personnel if the
grounding instructions are not completely understood, or if
in doubt as to whether the tool is properly grounded.
Use only 3-wire extension cords that have 3prong
grounding plugs and 3pole receptacles that accept the
tool's plug.
Repair or replace damaged or worn cord immediately.
2. Grounded, cord-connected tools intended for use on a
supply circuit having a nominal rating less than
150 volts:
This tool is intended for use on a circuit that has an outlet
that looks like the one illustrated in Sketch A in Figure 28.
The tool has a grounding plug that looks like the plug
illustrated in Sketch A in Figure 28. A temporary adapter,
which looks like the adapter illustrated in Sketches B and
C, may be used to connect this plug to a 2-pole receptacle
as shown in Sketch B if a properly grounded outlet is not
available. The temporary adapter should be used only until
a properly grounded outlet can be installed by a qualified
electrician. The green-colored rigid ear, lug, and the like,
extending from the adapter must be connected to a
permanent ground such as a properly grounded outlet box.
Grounding methods
GROUNDING
PIN
METAL SCREW
COVER OF GROUNDED
OUTLET BOX
<A> <B>
ADAPTER
<C>
GROUNDING
MEANS
GROUNDING
PIN
Fig. 28
<D>
Table 1
Minimum gage for cord
Effective date for Table 1 changed from November 1, 1995 to
November 11, 1996
Ampere Rating
More
Than
0
6
10
12
Not More
Than
6
10
12
16
Volts
120 V
240 V
Total length of cord in feet
25 ft. 50 ft. 100 ft. 150 ft.
50 ft. 100 ft. 200 ft. 300 ft.
AWG
18 16
16
14
18 16
14
12
16 16
14
12
14 12 Not Recommended
Additional safety instructions :
This milling machine is for indoor use only. Do not expose
to rain or use in damp locations.
Use only accessories recommended for this milling ma-
chine. Follow the instructions that accompany accessories.
Use of improper accessories may cause hazards.
Do not attempt to modify this tool or create accessories
not recommended for use with this tool. Any such
alternation or modification is misuse and could result in
hazardous condition leading to possible serious injury.
To avoid injury from unexpected starting or electrical
shock, do not plug the power cord into a power source
receptacle during unpacking and assembly. This cord must
remain unplugged whenever you are working on the milling
machine.
If any part is missing or damaged, do not plug the milling
machine in until the missing or damaged part is replaced,
and assembly is complete. To avoid electrical shock, use
only identical replacement parts when servicing grounded
tools.
For your safety, never connect the plug to the power
source receptacle until the assembly and adjustment steps
are completed, and you have read and understood the
safety and operating instructions.
To avoid injury from accidental start, make sure the switch
is in the OFF position and the plug is not connected to the
power source receptacle before changing any parts or
tools (i. e. miller)
To avoid injury from accidental start, make sure the switch
is in the OFF position and the plug is not connected to the
power source receptacle before making any adjustments.
For your own safety, do not plug the tool into the power
source receptacle or insert the switch key, until the parts
are correctly installed and adjustments have been made.
For your own safety, use only millers sized and recommen-
ded for this milling machine. Follow the instructions that
accompany the millers.
-5-
Free Datasheet http://www.datasheet4u.com/
5 Page | ||
| Páginas | Total 7 Páginas | |
| PDF Descargar | [ Datasheet MF70.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| MF70 | Fast Recovery Diode |  Dynex |
| MF70 | Micro Milling Machine | PROXXON |
| MF70 | Metal Film Resistors |  ASJ |
| MF70-1200 | Fast Recovery Diode | Dynex |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |