|
|
PDF MT0380-UV-A Data sheet ( Hoja de datos )
| Número de pieza | MT0380-UV-A | |
| Descripción | LED | |
| Fabricantes | Marktech | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de MT0380-UV-A (archivo pdf) en la parte inferior de esta página. Total 5 Páginas | ||
|
No Preview Available !
3Northway Lane North Latham,New York 12110.
Tollfree:1.800.984.5337
Phone:1.518.956.2980
Fax:1.518.785.4725
Http://www.marktechopto.com
SPECIFICATION
PART NO. : MT0380-UV-A
5.0mm ROUND LED LAMPwww.DataSheet.co.kr
ATTENTION
OBSERVE PRECAUTION
FOR HANDLING
ELECTRO STATIC
SENSITIVE
DEVICES
Datasheet pdf - http://www.DataSheet4U.net/
1 page  
Precautions:
TAKE NOTE OF THE FOLLOWING IN USE OF LED
1. Temperature in use
Since the light generated inside the LED needs to be emitted to outside efficiently, a resin with
high light transparency is used; therefore, additives to improve the heat resistance or moisture
resistance (silica gel , etc) which are used for semiconductor products such as transistors
cannot be added to the resin.
Consequently, the heat resistant ability of the resin used for LED is usually low; therefore,
please be careful on the following during use.
Avoid applying external force, stress, and excessive vibration to the resins and terminals at
high temperature. The glass transition temperature of epoxy resin used for the LED is
approximately 120-130 .
At a temperature exceeding this limit, the coefficient of liner expansion of the resin doubles or
more compared to that at normal temperature and the resin is softened.
If external force or stress is applied at that time, it may cause a wire rupture.
2. Soldering
Please be careful on the following at soldering.
After soldering, avoided applying external force, stress, and excessivewww.DataSheet.co.kr vibration until the
products go to cooling process (normal temperature), <Same for products with terminal leads>
(1) Soldering measurements:
Distance between melted solder side to bottom of resin shall be 1.6mm or longer.
(2) Dip soldering :
Pre-heat: 90 max. (Backside of PCB), Within 60 seconds.
Solder bath: 260 5 (Solder temperature), Within 5 seconds.
(3) Hand soldering: 350 max. (Temperature of soldering iron tip), Within 3 seconds.
3. Insertion
Pitch of the LED leads and pitch of mounting holes need to be same.
4. Others
Since the heat resistant ability of the LED resin is low, SMD components are used on the same
PCB, please mount the LED after adhesive baking process for SMD components. In case
adhesive baking is done after LED lamp insertion due to a production process reason, make
sure not to apply external force, stress, and excessive vibration to the LED and follow the
conditions below.
Baking temperature: 120 max. Baking time: Within 60 seconds.
If soldering is done sequentially after the adhesive baking, please perform the soldering after cooling down
the LED to normal temperature.
VER.: 01
Date: 2009/10/12
Page:
4/4
Datasheet pdf - http://www.DataSheet4U.net/
5 Page | ||
| Páginas | Total 5 Páginas | |
| PDF Descargar | [ Datasheet MT0380-UV-A.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| MT0380-UV-A | LED | Marktech |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |