|
|
PDF LE25LB1282TT Data sheet ( Hoja de datos )
| Número de pieza | LE25LB1282TT | |
| Descripción | Serial SPI EEPROM | |
| Fabricantes | Sanyo Semicon Device | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de LE25LB1282TT (archivo pdf) en la parte inferior de esta página. Total 14 Páginas | ||
|
No Preview Available !
www.DataSheet.co.kr
Ordering number : ENA1311C
LE25LB1282TT
Serial SPI EEPROM
(SPI Bus)(128Kbit)
Overview
The LE25LB1282TT is a 128Kbit EEPROM that supports serial peripheral interface (SPI). It realizes high speed operation
and high level reliability by incorporating SANYO’s high performance CMOS EEPROM technology. The interface is
compatible with SPI bus protocol, therefore, it is best suited for applications that require small-scale rewritable nonvolatile
parameter memory. Moreover, the LE25LB1282TT has a 64 bytes page rewrite function that provides rapid data rewriting.
Features
• Capacity
• Single supply voltage
• Serial interface
• Operating clock frequency
• Low current dissipation
• Page write function
• Rewrite time
• Number of rewrite times
• Data retention period
• High reliability
: 128Kbits (16K×8bits)
: 1.8V to 3.6V
: SPI Mode0, Mode3 supported
: 5MHz (2.5V to 3.6V), 3MHz (1.8V to 3.6V)
: Standby
: 3μA (max.)
: Active (Read) : 1mA (max.)
: Active (Rewrite) : 3mA (max.)
: 64bytes
: 10ms
: 106 times
: 20years
: Adopts SANYO’s proprietary symmetric memory array configuration (USP6947325)
Incorporates a feature to prohibit write operations under low voltage conditions.
* This product is licensed from Silicon Storage Technology, Inc. (USA), and manufactured and sold by SANYO Semiconductor Co., Ltd.
Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to
"standard application", intended for the use as general electronics equipment (home appliances, AV equipment,
communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be
intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace
instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety
equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case
of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee
thereof. If you should intend to use our products for applications outside the standard applications of our
customer who is considering such use and/or outside the scope of our intended standard applications, please
consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our
customer shall be solely responsible for the use.
Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate
the performance, characteristics, and functions of the described products in the independent state, and are not
guarantees of the performance, characteristics, and functions of the described products as mounted in the
customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent
device, the customer should always evaluate and test devices mounted in the customer's products or
equipment.
70611 SY/10511 SY/40809 SY/31809 SY JK/20080822-S00007 No.NA1311-1/14
Datasheet pdf - http://www.DataSheet4U.net/
1 page  
www.DataSheet.co.kr
LE25LB1282TT
Table 1 Command Settings
Command
1st bus
cycle
2nd bus
cycle
3rd bus
cycle
4th bus
cycle
Write enable
(WREN)
06h
Write disable
(WRDI)
04h
Status register read
(RDSR)
05h
Status register write
01h DATA
(WRSR)
Read
(READ)
03h
A15-A8
A7-A0
Write
(WRITE)
02h
A15-A8
A7-A0
PD *1
Explanatory notes for Table 1
The “h” following each code indicates that the number given is in hexadecimal notation.
Addresses A15 and A14 for all commands are “don’t care.”
*1: “PD” stands for page program data. Any amount of data from 1 to 64 bytes is input.
5th bus
cycle
PD *1
6th bus
cycle
PD *1
nth bus
cycle
PD *1
Figure 2 Serial Input Timing
(SPI Mode 0)
CS
SCK
SI
tCLS tCSS
tDS tDH
DATA VALID
tCPH
tCLHI tCLLO tCSH tCLH
SO
High Impedance
High Impedance
(SPI Mode 3)
CS
SCK
SI
tCLS
tCSS
tDS tDH
DATA VALID
tCLLO tCLHI
tCPH
tCSH tCLH
SO
High Impedance
High Impedance
No.NA1311-5/14
Datasheet pdf - http://www.DataSheet4U.net/
5 Page 
www.DataSheet.co.kr
LE25LB1282TT
5. Write (WRITE)
The LE25LB1282TT enables pages with up to 64bytes to be written. Any number of bytes from 1 to 64bytes can be
written within the same sector page (page addresses : A15 to A6). “Figure 9 Write” shows the write timing waveforms,
and Figure 12 shows a write flowchart. After the falling CS edge, the command (02H) is input followed by the 16-bit
addresses (Add). The write data is then loaded until the rising CS edge, and the internal addresses (A5 to A0) are
incremented (Add+1) every time the data is loaded in 1-byte increments. The data loading continues until the rising CS
edge. If the data loaded has exceeded 64bytes, the 64bytes loaded last are written. The write data must be loaded in
1-byte increments, and the write operation is not performed at the rising CS edge occurring at any other timing. The
write time is 10ms (max.) when 64bytes (1page) are written at one time.
Figure 9 Write
CS
SCK
SI
Mode3
Mode0
0 1 2 3 4 5 6 7 8 15 16 23 24 31 32 39 40 47
8CLK
02h
(00000010)
Add. Add.
(A15-A8) (A7-A0)
PD
(N)
PD
(N+1)
PD
(N+2)
Self-timed
Write Cycle
tWC
535
PD
(N+63)
SO
High Impedance
• Addresses A15 and A14 are “don’t care.”
6. Hold Function
Using HOLD pin, the hold function suspends serial communication (it places it in the hold status). “Figure 10 HOLD”
shows the timing waveforms. The device is placed in the hold status at the falling HOLD edge while the logic level of
SCK is low, and it exits from the hold status at the rising HOLD edge. When the logic level of SCK is high, HOLD must
not rise or fall. The hold function takes effect when the logic of CS is low, and the hold status is exited and serial
communication is reset at the rising CS edge. In the hold status, the SO output is in the high-impedance state, and SI
and SCK are “don’t care.”
Figure 10 HOLD
CS
SCK
Active
tHS
HOLD
Active
tHS
HOLD
SO
tHH tHH
tHHZ
tHLZ
High Impedance
No.NA1311-11/14
Datasheet pdf - http://www.DataSheet4U.net/
11 Page | ||
| Páginas | Total 14 Páginas | |
| PDF Descargar | [ Datasheet LE25LB1282TT.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| LE25LB1282TT | Serial SPI EEPROM | Sanyo Semicon Device |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |