Datenblatt-pdf.com


IT358 Schematic ( PDF Datasheet ) - INFINITRUE TECHNOLOGY

Teilenummer IT358
Beschreibung LOW POWER DUAL OPERATIONAL AMPLIFIER
Hersteller INFINITRUE TECHNOLOGY
Logo INFINITRUE TECHNOLOGY Logo 




Gesamt 8 Seiten
IT358 Datasheet, Funktion
www.DataSheet4U.net
LOW POWER DUAL OPERATIONAL AMPLIFIER
IT358
IT358
DESCRIPTION
The IT358 consists of two independent ,high
gain ,internally frequency compensated operational
amplifiers which were designed specifically to
operate from a single power supply over a wide
range of voltages.Operation from split power
supplies is also possible and the low power supply
current drain is independent of the magnitude of
the power supply voltage.
Application areas include transducer amplifiers.
DC agin blocks and all the conventional op amp
Circuits which now can be more easily.
Implemented in single power supply systems.For
Example,the IT358 can be directly operated off of
the standard -5Vpower supply voltage which is used
in digital systems and will easily provide the required
interface electronics without requiring the additional=15Vpower supplies.
UNIQUE CHARACTERISTICS
In the linear mode the input common-mode voltage range includes ground and the
Output voltage can also swing to ground .,even though operated from only a single
power
Supply voltage
The unity gain cross frequency is temperature compensated
The input bias current is also temperature compensated.
ADVANTAGES
Two internally compensated op amps.
Eliminates need for dual supplies.
Allows direct sensing near GND and Vout also goes to GND.
Compatible with all forms of logic.
Power drain suitable for battery operation
INFINITRUE TECHNOLOGY
1/8






IT358 Datasheet, Funktion
www.DataSheet4U.net
IT358
APPLICATION HINTS
The IT358 is op amps which operate with only a single power supply voltage, have
true-differential inputs, and remain in the linear mode with an input common-mode voltage
of 0V. These amplifiers operate over a wide range of power supply voltage with little
change in performance characteristics. At 25°C amplifier operation is possible down to a
minimum supply voltage of 2.3 V.
Precautions should be taken to insure that the power supply for the integrated circuit
never becomes reversed in polarity or that the unit is not inadvertently installed backwards
in a test socket as an unlimited current surge through the resulting forward diode within the
IC could cause fusing of the internal conductors and result in a destroyed unit.
Large differential input voltages can be easily accommodated and, as input differential
voltage protection diodes are not needed, no large input currents result from large
differential input voltages. The differential input voltage may be larger than V+ without
damaging the device. Protection should be provided to prevent the input voltages from
going negative more than -0.3V (at 25°C). An input clamp diode with a resistor to the IC
input terminal can be used.
To reduce the power supply current drain, the amplifiers have a class A output stage for
small signal levels which converts to class B in a large signal mode. This allows the
amplifiers to both source and sink large output currents. Therefore both NPN and PNP
external current boost transistors can be used to extend the power capability of the basic
amplifiers. The output voltage needs to raise approximately 1 diode drop above ground to
bias the on-chip vertical PNP transistor for output current sinking applications.
For ac applications, where the load is capacitively coupled to the output of the amplifier,
a resistor should be used, from the output of the amplifier to ground to increase the class A
bias current and prevent crossover distortion. Where the load is directly coupled, as in dc
applications, there is no crossover distortion.
Capacitive loads which are applied directly to the output of the amplifier reduce the loop
stability margin. Values of 50pF can be accomodated using the worst-case non-inverting
unity gain connection. Large closed loop gains or resistive isolation should be used if larger
load capacitance must be driven by the amplifier.
Output short circuits either to ground or to the positive power supply should be of short
time duration. Units can be destroyed, not as a result of the short circuit current causing
metal fusing, but rather due to the large increase in IC chip dissipation which will cause
eventual failure due to excessive function temperatures. Putting direct short-circuits on
more than one amplifier at a time will increase the total IC power dissipation to destructive
levels, if not properly protected with external dissipation limiting resistors in series with
the output leads of the amplifiers. The larger value of output source current which is
available at 25°C provides a larger output current capability at elevated temperatures (see
typical performance characteristics) than a standard IC op amp.
INFINTRUE TECHNOLOGY
6/8

6 Page







SeitenGesamt 8 Seiten
PDF Download[ IT358 Schematic.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
IT358LOW POWER DUAL OPERATIONAL AMPLIFIERINFINITRUE TECHNOLOGY
INFINITRUE TECHNOLOGY

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com       |      2020       |      Kontakt     |      Suche