|
|
Teilenummer | NL10276BC30-34D |
|
Beschreibung | LCD Module | |
Hersteller | NEC | |
Logo | ||
Gesamt 30 Seiten TFT COLOR LCD MODULE
NL10276BC30-34D
38cm (15.0 Type)
XGA
LVDS interface (1port)
PRELIMINARY DATA SHEET
DOD-PP-0753 (1st edition)
All information is subject to change without notice.
Please confirm the sales representative before
starting to design your system.
Document Number: DOD-PP-0 753(1st edition)
www.DPuatbaliSshheeedt4dUa.tnee: tMarch. 2009 CP(N)
1 © NEC LCD Technologies, Ltd.
2009 All rights reserved.
3. BLOCK DIAGRAM
Host LCD module (Product)
D0+ 100Ω
D0-
D1+
D1- 100Ω
D2+ 100Ω
D2-
D3+
D3- 100Ω
CLK+
CLK-
100Ω
MSL
DPS
GND
Note1
Note2
VCC
Fuse
FG
Note1
Note2
Anode 1-5
Cathode 1-5
Power supply
for gradation
DC/DC
converter
LCD panel signal processing board
5
5
NL10276BC30-34D
H-driver
3,072 lines
LCD panel
H: 1,024 × 3 (R, G, B)
V: 768
Backlight Note3
Note1: Relations between GND (Signal ground) and FG (Frame ground) in the LCD module is as
follows.
GND-FG
Connected
Note2: GND and FG must be connected to customer equipment's ground, and it is recommended that
GND and FG are connected together in customer equipment.
PRELIMINARY DATA SHEET DOD-PP-0753 (1st edition)
6
6 Page 4.4 POWER SUPPLY VOLTAGE SEQUENCE
NL10276BC30-34D
VCC
Note1
0V
ON
3.0V
0.1ms < Tr < 80ms
OFF
2.5V 3.0V
20ms max.
ON
Toff > 200ms
Display signals*,
Function signals
Note2
0V
0.01ms < t < 50ms
VALID period
0.01ms < t < 50ms
* These signals should be measured at the terminal of 100Ω resistance.
Note1: In terms of voltage variation (voltage drop) while VCC rising edge is below 3.0V, a protection
circuit may work, and then this product may not work.
Note2: Display signals (D0+/-, D1+/-, D2+/-, D3+/-, CLK+/-) and function signals (MSL, DPS) must
be Low or High impedance, exclude the VALID period (See above sequence diagram), in
order to avoid that internal circuit is damaged.
If some of display and function signals of this product are cut while this product is working,
even if the signal input to it once again, it might not work normally. VCC should be cut when
the display and function signals are stopped.
Note3: The backlight should be turned on within the valid period of display and function signals, in
order to avoid unstable data display.
4.4.2 Backlight lighting circuit
Display signals,
Function signals
Note1
Note2
VALID period
LED backlight: ON
Note1: These are the display and function signals for LCD panel signal processing board.
Note2: The backlight should be turned on within the valid period of display and function signals, in
order to avoid unstable data display.
PRELIMINARY DATA SHEET DOD-PP-0753 (1st edition)
12
12 Page | ||
Seiten | Gesamt 30 Seiten | |
PDF Download | [ NL10276BC30-34D Schematic.PDF ] |
Teilenummer | Beschreibung | Hersteller |
NL10276BC30-34BD | LCD Module | NLT |
NL10276BC30-34D | LCD Module | NEC |
NL10276BC30-34R | TFT COLOR LCD MODULE | NEC |
Teilenummer | Beschreibung | Hersteller |
CD40175BC | Hex D-Type Flip-Flop / Quad D-Type Flip-Flop. |
Fairchild Semiconductor |
KTD1146 | EPITAXIAL PLANAR NPN TRANSISTOR. |
KEC |
www.Datenblatt-PDF.com | 2020 | Kontakt | Suche |