Datenblatt-pdf.com


VX-015-1C23 Schematic ( PDF Datasheet ) - Omron Electronics

Teilenummer VX-015-1C23
Beschreibung Snap Action Switch
Hersteller Omron Electronics
Logo Omron Electronics Logo 




Gesamt 8 Seiten
VX-015-1C23 Datasheet, Funktion
Snap Action Switch
VX
Miniature Snap Action Switch
• Compact snap action switch with low force operation
• Wide variation extends from microload to 5 A switching
current, with shapes identical to those of the V-series
Miniature Basic Snap Action Switch.
• Internal hinge lever mechanism assures outstanding con-
tact reliability
• RoHS Compliant
Ordering Information
Actuator
Pin plunger
Short hinge lever
Hinge lever
Long hinge lever
Simulated roller lever
Short hinge roller lever
Hinge roller lever
Terminal Style
A
C2
A
C2
A
C2
A
C2
A
C2
A
C2
A
C2
OF max.
25 gf
50 gf
25 gf
50 gf
50 gf
30 gf
20 gf
30 gf
60 gf
30 gf
5A
VX-5-1A2
VX-5-1A3
VX-5-1C22
VX-5-1C23
VX-51-1A3
VX-51-1C23
VX-52-1A3
VX-52-1C23
VX-53-1A3
VX-53-1C23
VX-54-1A3
VX-54-1C23
VX-55-1A3
VX-55-1C23
VX-56-1A3
VX-56-1C23
Rated current
0.1 A
VX-01-1A2
VX-01-1A3
VX-01-1C22
VX-01-1C23
VX-011-1A3
VX-011-1C23
VX-012-1A3
VX-012-1C23
VX-013-1A3
VX-013-1C23
VX-014-1A3
VX-014-1C23
VX-015-1A3
VX-015-1C23
VX-016-1A3
VX-016-1C23
Model Number Legend
VX - -
1 2 345
1. Ratings
2.
www.DataSheet4U5.:com 5 A at 250 VAC
01: 0.1 A at 30 VDC
Actuator
3.
None: Pin plunger
1: Short hinge lever
2: Hinge lever
3: Long hinge lever
4.
4: Simulated roller lever
5: Short hinge roller lever
6: Hinge roller lever
Contact Form
5. Maximum Operating Force
1: SPDT
2: 25 gf
2: SPST-NC
3: 50 gf
3: SPST-NO
Terminals
Note: These OF values are for
the pin plunger models.
A: Solder terminals
C2: Quick-connect terminals (#187)
Snap Action Switch VX 135






VX-015-1C23 Datasheet, Funktion
Precautions
Correct Use
Mounting Direction
For a switch with an actuator, mount the switch in a direction where
the actuator weight will not be applied to the switch.
Since the switch is designed for a small load, its resetting force is
small. Therefore, resetting failure may occur if unnecessary load is
applied to the switch.
Operation
Keep the operation control completely separate from the actuator of
the switch, and push it down fully when starting operation. Do not dis-
place the operating position of the actuator when machining.
Consult OMRON in advance if the operating speed is to be extremely
slow, or if the pushbutton is to be set somewhere between the free
position and operating position.
Mount pin pushbutton switches so that stroke of the pushbutton and
the stroke of the operating control overlap on a vertical line. The
stroke of the switch, after operation, should be set to 60- 90% that of
standard OT (MIN operation).
Using Microloads
Using a model for ordinary loads to switch microloads may result in
faulty operation. Instead, use the models that are designed for micro-
loads and that operate in the following range;
0.16mA
30
26mA 100mA
24
Operating
Operating range
for micro load
models VX-01
range for
general-
load models
VX-5
12
Inoperable
range
5
1mA
100mA 160mA
0
0.1
1
10 100 1,000
Current (mA)
However, even when using microload models within the operating
range shown above, if inrush current or inductive voltage spikes
occur when the contact is opened or closed, it may increase contact
wear and so decrease the service life. Therefore, insert a contact
protection circuit where necessary.
Cautions
Handling
Be careful not to drop the switch. Doing so may cause damage to the
switch’s internal components because it is designed for a small load.
Solder Terminal Connection
Quickly finish the soldering of the lead wire to its terminal. Use a sol-
dering iron rated at 60W and preferably complete the soldering within
5 seconds.
Excess wattage or prolonged heating can deteriorate the characteris-
tics of the switch.
Insulation Distance
When mounting, make sure there is sufficient insulation distance
between the switch and its mounting panel. If it is insufficient, install
an insulation guard or separator. Always install an insulation guard or
separator when mounting the microswitch on a metallic body. Con-
tact your OMRON representative for information about insulation
guards and separators.
Application Environment
Do not use the Switch in locations that are subject to toxic gas, sili-
con, excessive dust, excessive dirt, high temperatures, high humidity,
sudden temperature changes, water splashes, or oil splashes.
Otherwise, damage resulting by faulty contact of the Switch contacts,
corrosion, or other causes, or other functional faults may occur.
Depending on environmental conditions, the switch should be
rechecked about 3 to 6 months after it has been assembled.
www.DataSheet4U.com
140 Snap Action Switch VX

6 Page







SeitenGesamt 8 Seiten
PDF Download[ VX-015-1C23 Schematic.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
VX-015-1C23Snap Action SwitchOmron Electronics
Omron Electronics

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com       |      2020       |      Kontakt     |      Suche