|
|
PDF MB90F583CA Data sheet ( Hoja de datos )
| Número de pieza | MB90F583CA | |
| Descripción | 16-bit Proprietary Microcontroller | |
| Fabricantes | FUJITSU | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de MB90F583CA (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
FUJITSU MICROELECTRONICS
DATA SHEET
DS07-13710-7E
16-bit Proprietary Microcontroller
CMOS
F2MC-16LX MB90580C Series
MB90583C/583CA/F583C/F583CA/F584C/F584CA/
MB90587C/587CA/V580B
■ DESCRIPTION
The MB90580C series is a line of general-purpose, Fujitsu Microelectronics 16-bit microcontrollers designed for
process control applications which require high-speed real-time processing, such as consumer products.
While inheriting the AT architecture of the F2MC*1 family, the instruction set for the F2MC-16LX CPU core of the
MB90580C series incorporates additional instructions for high-level languages, supports extended addressing
modes, and contains enhanced multiplication and division instructions as well as a substantial collection of
improved bit manipulation instructions. In addition, the MB90580C has an on-chip 32-bit accumulator which
enables processing of long-word data.
The peripheral resources integrated in the MB90580C series include: an 8/10-bit A/D converter, an 8-bit D/A
converter, UARTs (SCI) 0 to 4, an 8/16-bit PPG timer, 16-bit I/O timers (16-bit free-run timer, input capture units
(ICUs) 0 to 3, output compare units (OCUs) 0 and 1), and an IEBusTM controller *2.
*1: F2MC is the abbreviation of FUJITSU Flexible Microcontroller.
*2: IEBusTM is a trademark of NEC Corporation.
■ FEATURES
• Minimum execution time: 62.5 ns/4 MHz oscillation (Uses PLL clock multiplication) maximum multiplier = 4
• Maximum memory space
16 Mbyte
Linear/bank access
(Continued)
For the information for microcontroller supports, see the following web site.
This web site includes the "Customer Design Review Supplement" which provides the latest cautions on
system development and the minimal requirements to be checked to prevent problems before the system
development.
http://edevice.fujitsu.com/micom/en-support/
Copyright©2001-2009 FUJITSU MICROELECTRONICS LIMITED All rights reserved
2009.5
www.DataSheet.in
1 page  
MB90580C Series
(Continued)
Item Part number MB90587C/CA MB90583C/CA MB90F583C/CA MB90F584C/CA MB90V580B
16-bit
free run
timer
Number of channels: 1
Overflow interrupts
16-bit
I/O timer
Output
compare
(OCU)
Number of channels: 2
Pin input factor: A match signal of compare register
Input
capture
(ICU)
Number of channels: 4
Rewriting a register value upon a pin input (rising, falling, or both edges)
DTP/external
interrupt circuit
Number of inputs: 8
Started by a rising edge, a falling edge, an “H” level input, or an “L” level input.
External interrupt circuit or extended intelligent I/O service (EI2OS) can be used.
Delayed interrupt
generation module
An interrupt generation module for switching tasks used in real time operating systems.
UART0, 1, 2, 3, 4
Clock synchronized transmission (62.5 Kbps to 1 Mbps)
Clock asynchronized transmission (1202 bps to 9615 bps)
Transmission can be performed by bi-directional serial transmission or by master/slave
connection.
A/D converter
Resolution: 8/10-bit changeable
Number of inputs: 8
One-shot conversion mode (converts selected channel only once)
Scan conversion mode
(converts two or more successive channels and can program up to 8 channels.)
Continuous conversion mode (converts selected channel repeatedly)
Stop conversion mode (converts selected channel and stop operation repeatedly)
D/A converter
8-bit resolution
Number of channels: 2 channels
Based on the R-2R system
Low-power
consumption
(standby) mode
Sleep/stop/CPU intermittent operation/watch/hardware standby
Process
CMOS
Power supply voltage
for operation
4.5 V to 5.5 V*3
*1: Connect the oscillator to both terminals XA0 and XA1 for MB90F587C / 583C / F583C / F584C.
*2: It is setting of DIP switch S2 when Emulation pod (MB2145-507) is used.
Please refer to the MB2145-507 hardware manual (2.7 Emulator-specific Power Pin) about details.
*3: Varies with conditions such as the operating frequency (See section “■ ELECTRICAL CHARACTERISTICS”).
Assurance for the MB90V580B is given only for operation with a tool at a power supply voltage of 4.5 V to
5.5 V, an operating temperature of 0 to +25 °C, and an operating frequency of 1 MHz to 16 MHz.
■ PACKAGE AND CORRESPONDING PRODUCTS
Package
MB90583C/CA
FPT-100P-M20
FPT-100P-M06
: Available ×: Not available
MB90587C/CA MB90F584C/CA MB90F583C/CA
Note: : For more information about each package, see section “■ PACKAGE DIMENSIONS”.
DS07-13710-7E
5
www.DataSheet.in
5 Page 
MB90580C Series
Pin no.
Pin name
QFP*1 LQFP*2
Circuit
type
Function
General-purpose I/O port.
P43
This pin serves as an open-drain output port with OD43 in the open-
drain control setting register (ODR4) set to “1”. [The pin is disabled
21 19
E with the input setting (DDR4 register: D43=“0”).]
(CMOS/H) UART1 serial data input (SIN1) pin.
SIN1
When UART1 is operating for input, this input is used as required and
thus the output from any other function to the pin must be off unless
used intentionally.
General-purpose I/O port.
22
20
P44
This pin serves as an open-drain output port with OD44 in the open-
E drain control setting register (ODR4) set to “1”. [The pin is disabled
(CMOS/H) with the input setting (DDR4 register: D44=“0”).]
SOT1
UART1 serial data output pin (SOT1).
This pin is enabled with the UART1 serial data output enabled.
General-purpose I/O port.
24
22
P45
This pin serves as an open-drain output port with OD45 in the open-
E drain control setting register (ODR4) set to “1”. [The pin is disabled
(CMOS/H) with the input setting (DDR4 register: D45=“0”).]
SCK1
UART1 serial clock I/O pin (SCK1).
This pin is enabled with the UART1 clock output enabled.
General-purpose I/O port.
25
23
P46
This pin serves as an open-drain output port with OD46 in the open-
E drain control setting register (ODR4) set to “1”. [The pin is disabled
(CMOS/H) with the input setting (DDR4 register: D46=“0”).]
ADTG
External trigger input pin (ADTG) for the A/D converter.
General-purpose I/O port.
26
24
P47
E This pin serves as an open-drain output port with OD47 in the open-
(CMOS/H) drain control setting register (ODR4) set to “1”. [The pin is disabled
with the input setting (DDR4 register: D47=“0”).]
P50 General-purpose I/O port.
AN0 Analog input pin (AN0) for use during A/D converter operation.
38
36
SIN3
G UART3 serial data input pin (SIN3).
(CMOS/H) When UART3 is operating for input, this input is used as required and
thus the output from any other function to the pin must be off unless
used intentionally.
P51 General-purpose I/O port.
39
37
AN1
SOT3
G Analog input pin (AN1) for use during A/D converter operation.
(CMOS/H) UART3 serial data output pin (SOT3).
This pin is enabled with the UART3 serial data output enabled.
*1: FPT-100P-M06
*2: FPT-100P-M20
(Continued)
DS07-13710-7E
11
www.DataSheet.in
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet MB90F583CA.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| MB90F583C | 16-bit Proprietary Microcontroller | FUJITSU |
| MB90F583CA | 16-bit Proprietary Microcontroller | FUJITSU |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |