|
|
Teilenummer | TZA1049 |
|
Beschreibung | 4-channel BTL driver | |
Hersteller | NXP Semiconductors | |
Logo | ||
Gesamt 17 Seiten INTEGRATED CIRCUITS
DATA SHEET
www.DataSheet4U.com
TZA1049
4-channel BTL driver for
CD/DVD drives
Product specification
2004 Mar 09
Philips Semiconductors
4-channel BTL driver for CD/DVD drives
Product specification
www.DataSheet4U.com
TZA1049
VCC 1
RADOUTN 2
FOCOUTP 3
GND 4
FOCOUTN 5
RADOUTP 6
VCC 7
28 VOUT3.3
27 VFBIN3.3
26 VOUT1.8
25 VFBIN1.8
24 MUTE
23 RADIN
22 FOCIN
TZA1049TH
VCC 8
SLOUTP 9
SLOUTN 10
GND 11
MOTOUTP 12
MOTOUTN 13
VCC 14
21 SLIN
20 VBIASIN
19 GND
18 VBIASOUT
17 MOTBIAS
16 MOTIN1
15 MOTIN2
mce479
Fig.2 Pin configuration.
7 FUNCTIONAL DESCRIPTION
7.1 General notes
1. The integral thermal shut-down circuit mutes the
output current when the chip temperature reaches
175 °C (typical). The hysteresis is set to 25 °C
(typical), so the circuit will restart when the chip
temperature falls to 150 °C (typical).
2. Mute mode is activated when the voltage at pin MUTE
is below 0.5 V, and deactivated when the voltage at
pin MUTE is above 1.2 V. In mute mode, both positive
and negative output terminals will be at
high-impedance state. However, the 3.3 V and 1.8 V
outputs are not affected.
3. It is recommended that a 220 µF decoupling capacitor
is connected between pins VCC and pin GND and
physically located as close as possible to these supply
pins.
4. The positive outputs of the focus, radial and sled driver
channels are in phase with their respective input
signals. The positive output of the spindle driver
channel is in phase with the input signal on
pin MOTIN1.
5. The values of the resistors connected to each input
channel must be equal to, or larger than, 4.7 kΩ to
ensure that the gain of each input stage is less than, or
equal to 1.
6. The GND pins are internally connected to heat
dissipation fins within the package. You must ensure
that these pins are connected to an external ground.
7. The 1.65 V bias voltage output from pin VBIASOUT is
derived from the internal 3.3 V generator/regulator,
and will be affected by any variation in the 3.3 V
generator/regulator voltage.
2004 Mar 09
6
6 Page Philips Semiconductors
4-channel BTL driver for CD/DVD drives
Product specification
www.DataSheet4U.com
TZA1049
handbook, full pagewidth
12 V
220 µF
radial focus
coil coil
12 V
1
2
3
4
5
6
7
28 Q1
27
26 Q2
25
24
23
22
47 µF
3.3 V
47 µF
1.8 V
12 V
M
loading
motor
TZA1049
12 V
sled M
motor
spindle M
motor
8
9
10
11
12
13
14
21
20
19
18
17
16
15
SLED FOCUS RADIAL
COIL COIL COIL
SERVO/COIL DRIVER
SPINDLE
MOTOR1
FORWARD
MUTE
MICROCONTROLLER
REVERSE
MCE482
2004 Mar 09
Fig.6 Spindle motor single-ended application.
12
12 Page | ||
Seiten | Gesamt 17 Seiten | |
PDF Download | [ TZA1049 Schematic.PDF ] |
Teilenummer | Beschreibung | Hersteller |
TZA1045 | Photodiode and amplifier IC for CD and DVD applications | NXP Semiconductors |
TZA1045TS | Photodiode and amplifier IC for CD and DVD applications | NXP Semiconductors |
TZA1046 | Photodiode and amplifier IC | NXP Semiconductors |
TZA1047 | Analog Processor | Philips |
TZA1048 | 4-channel BTL driver | NXP Semiconductors |
Teilenummer | Beschreibung | Hersteller |
CD40175BC | Hex D-Type Flip-Flop / Quad D-Type Flip-Flop. |
Fairchild Semiconductor |
KTD1146 | EPITAXIAL PLANAR NPN TRANSISTOR. |
KEC |
www.Datenblatt-PDF.com | 2020 | Kontakt | Suche |