|
|
PDF GG1206N8SKN1T Data sheet ( Hoja de datos )
| Número de pieza | GG1206N8SKN1T | |
| Descripción | Display | |
| Fabricantes | Solomon | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de GG1206N8SKN1T (archivo pdf) en la parte inferior de esta página. Total 31 Páginas | ||
|
No Preview Available !
00000514
www.DataSheet4U.com
KAOHSIUNG FACTORY : NO. 18 Ta-Yeh St., Ta-Fa Industrial Park, Ta-Liao
Hsiang, Kaohsiung Hsien 831, TAIWAN , R.O.C.
TEL : 886-7-788-6800
FAX : 886-7-788-6806~8
PART NO : GG1206N8SKN1T
FOR MESSRS :
CONTENTS
NO.
1.
2.
3.
4.
5.
6.
7.
8.
ITEM
COVER
RECORD OF REVISION
GENERAL SPECIFICATION AND MECHANICAL DATA
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL AND OPTICAL CHARACTERISTICS
OUTLINE DIMENSION AND INTERFACE PIN CONNECTION
BLOCK DIAGRAM AND POWER SUPPLY
DISPLAY CONTROL INSTRUCTIONS
PAGE
1
2
3
4
5~7
8~11
13
14~31
Accepted by :
Proposed by :
Date : 10,25,2002
SOLOMON GOLDENTEK DISPLAY CORP.
GG1206N8SKN1TTEL : 886-7-788-6800 FAX : 886-7-788-6806~8
REV : 1
PAGE : 1
1 page  
00000514
5. ELECTRICAL AND OPTICAL CHARACTERISTICS
www.DataSheet4U.com
5.1 ELECRICAL CHARACTERISTICS
Ta = 25℃
VDD = 2.4V~6.0V
ITEM
LOGIC CIRCUIT
POWER SUPPLY
VOLTAGE
SYMBOL
VDD-VSS
CONDITION
–––––
INPUT VOLTAGE
VOH
NOTE (1)
INPUT VOLTAGE
VOL
NOTE (1)
LOGIC CIRCUIT
POWER SUPPLY
CURRENT
VDD-VSS
IDD =5.0V
RECOMMENDED
VDD - VO
Ta = 0℃
LCD DRIVING
DUTY = 1/64
VOLTAGE (NOTE 1)
∮ = 10°
Ta = 25℃
Ta = 50℃
MIN.
2.4
TYP. MAX. UNIT
------ 6.0
V
0.7*VDD –––– VDD V
GND –––– 0.3*VDD V
–––– 1.0
3.0 mA
––––
––––
––––
-------
(8.8)
------
––––
––––
––––
V
V
V
NOTE (1): CS1, CS2, R/W, D/I, DB0~DB7, E, RST
NOTE (2): RECOMMENDED LCD DRIVING VOLTAGE MAY FLUCTUATE
ABOUT ± 0.5V BY EACH MODULE.
SOLOMON GOLDENTEK DISPLAY CORP.
GG1206N8SKN1TTEL : 886-7-788-6800 FAX : 886-7-788-6806~8
REV : 1
PAGE : 5
5 Page 
Pin Name
CLS
M/S
CL
FR
/DOF
FRS
IRS
/HPM
SEG0
to
SEG131
00000514
www.DataSheet4U.com
I/O Function
I Terminal to select whether or enable or disable the displa clock internal oscillator circuit.
CLS=“H”:Internal oscillator circuit is enabled
CLS=“L”:Internal oscillator circuit is disabled(requires external input)
When CLS=“L”,input the displayclock through the CL terminal.
I This terminalselects the master/slave operation for the SED1565 Series chips. Master operation outputs the timing
signals that are required for the LCD display , while slave operation inputs the timing signals required for the liquid
crystal display ,synchronizing the liquid crystal display system.
M/S=“H”:Master operation M/S=“L”:Slave operation
The following is true depending on the M/S and CLS status:
M/S CLS Oscillator Circuit Power Supply Circuit CL
FR
FRS DOF
“H” “H”
Enable
Enable
Output
Output
Output Output
“L” Disable
Enable
Iput
Output
Output Output
“L” “H”
“L”
Disable
Disable
Disable
Disable
Iput
Iput
Output
Iput
Iput
Iput
Output
Iput
I/O This is the display clock input terminal
The following is true depending on the M/S and CLS status.
M/S CLS
“H” “H”
“L”
“L” “H”
“L”
CL
Output
Input
Input
Input
When the SED 1565 Series chips is used in master/slave mode,the various CL terminal must e connected.
I/O This is the liauid crystal alternating current signal I/O terminal.
M/S =“H”: Output M/S=“L”:Input
When the SED1565 Series chip is used in master/slave mode,the various FR terminals must be connected.
I/O This is the liquid crystal display blanking control terminal.
M/S=“H”:Output
M/S=“L”:Input
When the SED1565 SERies chip used in master/slave mode ,the various /DOF terminal must be connected.
O This is the output terminal for the static drive.
This is terminal is only enabled when the static indicator display is ON when in master operation mode,andis used in
conjunction with the FR terminal.
I This terminal selects the resistors for the V5 voltage level adjustment.
IRS=“H”:Use the internal resistors
IRS=“L”:Do not use the internal resistors. The V5 voltage level is regulated by an external resistive voltage divider
attached to the VR terminal.
This pin is enabled only when the master operation mode is selected.
It is fixed to either “H” or “L” when the slave opertion mode is selected.
I This is the power cotrol terminal for the power supply circuit for liquid crystal drive.
/HPM=“H”: Normal mode
/HPM=“L”:High power mode
This pin is enabled only when the master opertion mode is selected.
It is fixed to either “H” or “L” when the slave opertion mode is selected.
O These are the liquid crystal segment drive outputs. Through a combination of the contents of the display RAM and
with the FR signal , a singale level is selected from VDD,V2,V3,and V5.
RAM DATA
FR
Output Voltage
Normal Display
Reverse Display
HH
VDD
V2
HL
V5
V3
L
L
Power save
H
L
-----
V2 VDD
V3 V5
VDD
SOLOMON GOLDENTEK DISPLAY CORP.
TEL : 886-7-788-6800 FAX : 886-7-788-6806~8
GG1206N8SKN1T
REV : 1
PAGE : 11
11 Page | ||
| Páginas | Total 31 Páginas | |
| PDF Descargar | [ Datasheet GG1206N8SKN1T.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| GG1206N8SKN1T | Display | Solomon |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |