Datenblatt-pdf.com


SC-AK200 Schematic ( PDF Datasheet ) - Panasonic

Teilenummer SC-AK200
Beschreibung (SC-AKxx0 ) CD Stereo System
Hersteller Panasonic
Logo Panasonic Logo 




Gesamt 30 Seiten
SC-AK200 Datasheet, Funktion
www.datasheet4u.com
The illustrations show SC-AK500.
CD Stereo System
Operating Instructions
Model No. SC-AK500
SC-AK490
SC-AK300
SC-AK200
P PC
Before connecting, operating or adjusting this product, please read these
instructions completely.
Please keep this manual for future reference.
RQT6085-4P






SC-AK200 Datasheet, Funktion
www.datasheet4u.com
1
3
2
Connections
Basic connections (for supplied
accessories)
Plug the AC power supply cord into a household AC outlet only
after all other connections have been made.
To prepare the antenna wires and speaker cords, twist the vinyl
cover tip and pull off.
1
1
2
4
FM
(
ANT
)
GND
2
Adhesive tape
FM indoor antenna
AM loop antenna
AM ANT
LOOP
EXT
3
1
2
Red (+)
Black (–)
Blue (–)
Gray (+)
Gray
Blue
Black
Red
1 Connect the FM indoor antenna.
Tape the antenna to a wall or column, in a position where radio
signals are received with the least amount of interference.
Note
For best reception sound quality:
An FM outdoor antenna is recommended. (See page 7.)
2 Connect the AM loop antenna.
After attaching the antenna, turn on the system and tune in a
broadcast station. Put the antenna where the reception is best
and interference is minimal.
3 Connect the speaker cables.
Connect each end of the speaker cables to the terminal lever of
the same color so (+) and (–) are correct. Never allow the
exposed wires to contact each other when connected.
Incorrect connection can damage the unit.
Caution
Use only the supplied speakers.
The combination of the main unit and speakers provide the
best sound. Using other speakers can damage the unit and
sound quality will be negatively affected.
Caution
Use the speakers only with the recom-
mended system.
Failure to do so may lead to damage to the
amplifier and/or the speakers, and may result
in the risk of fire.
Consult a qualified service person if damage
has occurred or if you experience a sudden
change in performance.
Do not attach these speakers to walls or
ceilings.
4 Connect the AC power supply cord.
Note
The included AC power supply cord is for use with this unit
only. Do not use it with other equipment.
6
RQT6085

6 Page









SC-AK200 pdf, datenblatt
www.datasheet4u.com
1
3
1 TUNER/BAND
2 PLAY MODE
3 REW
FF
4
DOWN VOL UP
A
PLAY MODE
12
RQT6085
4
2
PLAY MODE
Listening to radio broadcasts
1 Press [TUNER/BAND] to select band.
The unit comes on automatically.
Every time you press the button:
FM AM
2 Press [PLAY MODE] on the remote
control to select “MANUAL”.
Every time you press the button:
MANUAL PRESET.
3 Press [g/REW/4] or [3/FF/f] to
select the frequency of the required
station.
“TUNED” is displayed when a radio station is tuned.
“ST” is displayed when a stereo FM broadcast is being
received.
4 Adjust the volume.
Auto tuning
Press and hold [g/REW/4] or [3/FF/f] for a moment until the
frequency starts changing rapidly. The unit begins auto tuning, stop-
ping when it finds a station.
Auto tuning may not function when there is excessive interference.
To cancel auto tuning, press [g/REW/4] or [3/FF/f] once
again.
A If noise is excessive in FM
Remote control only
Press and hold [PLAY MODE] to display
“MONO”.
This mode improves sound quality if reception is weak, but
broadcasts will be heard in monaural.
Press and hold [PLAY MODE] again to cancel the mode.
“MONO” goes out. MONO is also cancelled if the frequency is
changed.
Turn off “MONO” for normal listening. Stereo and monaural
broadcasts are automatically played as they are received.
FM allocation setting
Main unit only
By adjusting the allocation, you can enable this tuner to receive FM
broadcasts allocated in 0.1 MHz steps.
Press and hold [TUNER / BAND]. After a few seconds, the display will
change to a flashing display of the current minimum FM frequency.
If you continue to hold the button down, the minimum frequency will
change. Release the button at this time.
To return to the original frequency indication, repeat above.
Notes
After changing the “allocation” setting, the frequencies you previously
preset in the memory will be cleared.
Sound is momentarily interrupted if you load/unload tapes while
listening to an AM broadcast.

12 Page





SeitenGesamt 30 Seiten
PDF Download[ SC-AK200 Schematic.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
SC-AK200(SC-AKxx0 ) CD Stereo SystemPanasonic
Panasonic

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com       |      2020       |      Kontakt     |      Suche