|
|
Número de pieza | TL-WA501G | |
Descripción | 54M Wireless Access Point | |
Fabricantes | TP-Link | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de TL-WA501G (archivo pdf) en la parte inferior de esta página. Total 44 Páginas | ||
No Preview Available ! www.DataSheet4U.com
TL-WA501G
54M Wireless Access Point
Rev: 1.0.2
1910010027
1 page www.DataSheet4U.com
V
5 Page TL-WA501G 54M Wireless Access Point User Guide
¾ There are two ways to reset the AP's factory defaults:
www.DataSheet4U.com
• Use the Factory Defaults function on System Tools -> Factory Defaults page in the
AP's Web-based Utility.
• Use the Factory Default Reset button: First, turn off the AP's power. Second, press and
hold the default reset button then turn on the AP's power, until the system LED lights up
(about 3 seconds). Last, release the reset button and wait for the AP to reboot.
) Note:
Ensure the AP is powered on before it restarts completely.
¾ One LAN 10/100Mbps RJ45 port for connecting the AP to hub or switch
¾ AC power socket: only use the power adapter supplied with the TL-WA501G 54Mbps
Wireless Access Point, use of a different adapter may result in product damage.
2.3 System Requirements
¾ Broadband Internet Access Service (DSL/Cable/Ethernet)
¾ One DSL/Cable Modem that has an RJ45 connector
¾ A Ethernet broadband router
¾ TCP/IP protocol must be installed on each PC
¾ Web browser, such as Microsoft Internet Explorer 5.0 or later, Netscape Navigator 6.0 or later
¾ 802.11g or 802.11b-compliant devices, such as the TL-WN510G Wireless Adapter
2.4 Installation Environment Requirements
¾ Not in direct sunlight or near a heater or heating vent
¾ Not cluttered or crowded. There should be at least 2 inches (5 cm) of clear space on all sides
of the AP
¾ Well ventilated (especially if it is in a closet)
¾ Operating temperature: 0℃~40℃ (32℉~104℉)
¾ Operating Humidity: 10%~90%RH, Non-condensing
2.5 Connecting the Device
Figure 2-3 is an example of an infrastructure network incorporating the TL-WA501G. An
Infrastructure network contains an access point or a wireless router. For a typical connection of
the AP, please do the following:
1. You will need broadband Internet access (a Cable or DSL-subscriber line into your home or
office). Consult with your Cable or DSL provider for proper installation of the modem.
2. Connect the Cable or DSL modem to a Router. Quickly install the router.
3. Locate an optimum location for the AP. The best place is usually near the center of the area
in which your PC(s) will wirelessly connect. The place must accord with the Installation
Environment Requirements.
4. Adjust the direction of the antenna. Normally, upright is a good direction.
3
11 Page |
Páginas | Total 44 Páginas | |
PDF Descargar | [ Datasheet TL-WA501G.PDF ] |
Número de pieza | Descripción | Fabricantes |
TL-WA501G | 54M Wireless Access Point | TP-Link |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |