|
|
PDF EE-SPX613 Data sheet ( Hoja de datos )
| Número de pieza | EE-SPX613 | |
| Descripción | An Ideal Photomicrosensor | |
| Fabricantes | Omron Electronics | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de EE-SPX613 (archivo pdf) en la parte inferior de esta página. Total 5 Páginas | ||
|
No Preview Available !
EE-SPX613
www.DataSheet4U.com
An Ideal Photomicrosensor for
Detecting Liquid Levels in
Transparent Pipes
Incorporates a Sensitivity Selector,
Built-in Amplifier, and Operation Mode
Selector
Tie-wrap and rubber tube provided to
prevent slippage
Suitable for any 6- to 13-mm diameter
transparent or semi-transparent pipe
with a wall thickness of 1 mm
Built-in amplifier saves space and wiring
effort
Compact size is ideal for the
miniaturization of equipment
Uses a talc-free cable that is ideal for
equipment used for the manufacturing
of semiconductors
Ordering Information
Appearance
Detection method
Through-beam (with groove)
Output configuration
Dark-ON or light ON
(selectable)
Part number
EE-SPX613
1 page  
EE-SPX613
EE-SPX613
! Caution
Mwowuwn.DtiantagSheet4U.com
Always use supporting belts and slip protection tubes, which are
provided with the EE-SPX613, when attaching the EE-SPX613 to
an appropriate pipe, as shown in the following illustration. Make
sure that the pipe is in the center of the sensor groove and not
lifted from the pedestal.
When tightening the supporting belts, make sure that the pipe will
not be deformed.
Slip protection
tubes
Supporting belts
Power Supply
Ground the FG and GND terminals if a standard switching
regulator is used to supply power to the EE-SPX613, or the
EE-SPX613 may malfunction .
Operating Environment
The EE-SPX613 is not watertight. Do not use the EE-SPX613
outdoors.
Do not use the EE-SPX613 in places where water, oil, or
chemicals may splash or be sprayed onto the unit.
The exterior coverings of the EE-SPX613 are made of
polycarbonate. Keep the coverings away from any alkaline,
aromatic hydrocarbon, or aliphatic chloride hydrocarbon solvent,
all of which will damage the coverings.
Pipe
Pedestal
Sensor
Others
• The EE-SPX613 requires 10 ms to be in stable operation
after power is supplied.
If two power supplies are used for the EE-SPX613 and load
respectively, be sure to supply power to the EE-SPX613
before supplying power to the load.
• If there is a high-tension line near the cable, wire the cable
through an independent metal conduit to protect the
EE-SPX613 from damage or malfunction.
• Do not attach the EE-SPX613 to improper pipes, such as
non-transparent pipes, or the EE-SPX613 may not operate
properly.
• Do not impose any excessive force on the cable.
Do not pull the cable with a force exceeding 30 N.
• Use an extension cable with conductors having a total cross-
sectional area of 0.15 mm2 (i.e., AWG26) and a total cable
length of 5 m maximum.
• Do not impose a force exceeding 5 N on the operation mode
selector or sensitivity selector.
NOTE: DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters to inches divide by 25.4.
OOmMroRnOENuEroLpEeCBT.RV.OENMICAS-I,SIDNC, t.el:+31 23 5681390, fax:+31 23 5681397, http://www.OeuM.oRmOrNonC.cAoNmA/eDmAa, INC.
One East Commerce Drive
885 Milner Avenue
Schaumburg, IL 60173
Scarborough, Ontario M1B 5V8
1-800-55-OMRON
416-286-6465
Cat. No. EO5DAX4
1/99
Specifications subject to change without notice.
Printed in U.S.A.
5 Page | ||
| Páginas | Total 5 Páginas | |
| PDF Descargar | [ Datasheet EE-SPX613.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| EE-SPX613 | An Ideal Photomicrosensor | Omron Electronics |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |