|
|
PDF MIL-P-23377G Data sheet ( Hoja de datos )
| Número de pieza | MIL-P-23377G | |
| Descripción | Polyamide Epoxy Primer | |
| Fabricantes | Aircraft | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de MIL-P-23377G (archivo pdf) en la parte inferior de esta página. Total 1 Páginas | ||
|
No Preview Available !
www.pwpaints.com
Pacific Western Paints Ltd.
MIL-P-23377G
POLYAMIDE EPOXY PRIMER- AIRCRAFT
www.DataSheet4U.com
TECHNICAL DATA SHEET
DESCRIPTION:
MIL-P-23377G is a two component, corrosion inhibiting, polyamide primer. This epoxy primer offers
excellent corrosion and chemical resistance over properly prepared aluminum and steel substrates.
This primer meets Type 1 (standard pigments), Class C (strontium chromate) and was designed to be
topcoated with urethane or epoxy topcoats such as MIL-C-83286B, MIL-C-85285C or MIL-C-22750D.
PROPERTIES:
ADVANTAGES:
COLOR
SOLIDS by volume
Mix Ratio
Dry Film Thickness
Dry Times @77 F
Recoat
Pot Life @ 77 F
VOC (maximium)
Chromate Yellow
57%
4-1 by volume
with part "B" catalyst
.9 mils (minimum)
Tack Free 5hrs *
Dry 8 hrs *
Full Cure 7 days *
1 hr. minimum *
3 days maximum *
4 hrs.*
420 g/L
Corrosion Resistant
Chemical Resistant
Meets Military Specification
Meets ASTM Standards
Surface Prep & Primer (recommended)
Aluminum:
Solvent wash
Alumiprep- Etch & Clean
Alodine- Chrome Conversion Coating
Prime MIL-P-23377 @ .9 mils dry. (minimum)
SAFETY:
Refer to Material Safety Data Sheets before use
Shelf Life @ 77 F 12 months ( D.M.)
Reducer
MIL-T-81772B ty 2
(Reduction for conventional spray applic. 4-1-1)
S.F. Coverage
1100 sq/ft gal. ***
* times will vary with, humidity,temperature
and film thickness.
*** @ 100% transfer efficiency
Distributed by:
PACIFIC WESTERN PAINTS LTD.
AIRCRAFT COATINGS & RESINS
151- 5489 Byrne Road, Burnaby, BC, Canada, V5J 3J1
Phone (604)432-6111 or (604)430-4151
Fax (604)432-7006 e-mail [email protected]
Directions for use:
Mix primer part"A" 4-1 by volume with primer catalyst part"B". Stir thoroughly. Thin as needed with
MIL-T-81772B ty2 reducer. Apply one full wet coat using 45-55 PSI ( conventional spray) at the gun.
If a second coat is desired allow 10-15 minutes dry time between coats. Allow the final coat to dry a
minimum of 1 hr. @77 F. Topcoat within 1-2 hours. If primer has been left to dry over 24 hours or has
been baked, the surface must be abraded to achieve satisfactory adhesion.
NOTE: Never "DRY SPRAY" primers, they need a wet coat to flow into conversion coatings and sand
scratches. Refer to M.S.D.S. before use.
1 page | ||
| Páginas | Total 1 Páginas | |
| PDF Descargar | [ Datasheet MIL-P-23377G.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| MIL-P-23377G | Polyamide Epoxy Primer | Aircraft |
| MIL-P-23377H | Polyamide Epoxy Primer | Aircraft |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |