|
|
PDF Socket462 Data sheet ( Hoja de datos )
| Número de pieza | Socket462 | |
| Descripción | AMD Processor Installation Guide | |
| Fabricantes | AMD | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de Socket462 (archivo pdf) en la parte inferior de esta página. Total 20 Páginas | ||
|
No Preview Available !
23986—December 2000
Socket A AMD Processor Installation Guide
www.DataSheet4U.com
Socket A
AMD Processor
Installation Guide
Thank you for purchasing a Socket A AMD processor.
Before installing the new AMD processor in a system,
please review this installation guide in its entirety.
Note: The product(s) received may vary in appearance from the products illustrated.
.
Failure to install the AMD Athlon™ or the AMD Duron™ processor properly
may adversely affect operation and may void your warranty coverage.
DO NOT install the processor if it has been damaged!
1
1 page  
23986—December 2000
Socket A AMD Processor Installation Guide
3. Figure 3 shows the underside (pin side) of the processor. Notice how the pin array
at the two upper corners in the picture are angled and there are no pins in either
top corner. Notice also that there are no pin positions in the top corners of the
socket (near where it is labeled “Socket 462”). The processor must be positioned
so the processor and socket pin patterns match. When positioned properly, the 45°
cut corner of the processor will be next to the release pivot.
www.DataSheet4U.com
Corners with
Missing Pins
Missing Pin
Positions
Figure 3. Underside of the Processor Showing Pin Corner Keys
4. Figure 4 shows the processor dropping into the socket. Notice how the corner
located near the release lever pivot is the 45° cut corner. This is verification that
the processor has been installed properly.
It should take no significant force to install the processor. This is a zero insertion
force socket (often referred to as a ZIF socket). If the processor does not fall into
the socket, check the pin alignment and make sure that the release lever is raised
up completely. If the installation of the processor requires any significant amount
of force, then something is wrong. (Check the pins, and lever position.)
45° Cut
Corner
Figure 4. Placing the Processor in the Socket
5
5 Page 
23986—December 2000
Socket A AMD Processor Installation Guide
11. Figure 11 shows a side view of the heatsink with the retaining clip at the bottom
of the heatsink. Make sure that the retaining clip is in this position before trying
to install the heatsink. Notice that the clip is not symmetrical. The long end
always attaches to the top of the socket (the end that reads “Socket 462”), while
the short end engages the bottom of the socket. No matter which heatsink is used,
the clip is always installed in the same manner.
For best results, always install the processor and its heatsink before installing any
memory modules.
Also notice how the heatsink sits on the rubber pads. These pads are important to
www.DataSheet4U.comthe proper installation of the heatsink, because they prevent the heatsink from
rocking and cracking the processor die. THE PADS ARE ESSENTIAL. DO NOT
REMOVE THEM!
Figure 11. Side View of Heatsink and Clip on an Socket A AMD Processor
11
11 Page | ||
| Páginas | Total 20 Páginas | |
| PDF Descargar | [ Datasheet Socket462.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| Socket462 | AMD Processor Installation Guide | AMD |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |