Datenblatt-pdf.com


BETA58A Schematic ( PDF Datasheet ) - Shure

Teilenummer BETA58A
Beschreibung Microphone user guide
Hersteller Shure
Logo Shure Logo 




Gesamt 12 Seiten
BETA58A Datasheet, Funktion
Model BETA 58AR User Guide
www.DataSheet4U.com
MODEL BETA 58AR
SUPERCARDIOID DYNAMIC VOCAL MICROPHONE
GENERAL
The Shure BETA 58A is a high-output supercardioid dy-
namic vocal microphone designed for professional sound re-
inforcement and project studio recording. It maintains a true
supercardioid pattern throughout its frequency range. This
insures high gain before feedback, maximum isolation from
other sound sources, and minimum off–axis tone coloration.
The BETA 58A has a shaped frequency response that is
ideal for close–up vocals. The superb performance of this
microphone is not affected by rough handling because of its
rugged construction, proven shock mount system, and hard-
ened steel mesh grille. Typical applications for the BETA 58A
include lead vocals, backup vocals and speech.
FEATURES:
S Frequency response tailored for vocals, with brightened
midrange and bass rolloff to control proximity effect
S Uniform supercardioid pattern for high gain before
feedback and superior rejection of off–axis sound
S Neodymium magnet for high signal–to–noise output
S Hardened steel mesh grille that resists wear and abuse
S Advanced pneumatic shock mount system that minimizes
transmission of mechanical noise and vibration
S Minimally effected by varying load impedance
S Legendary Shure quality and reliability
2003, Shure Incorporated
27B2796 (Rev. 3)
APPLICATION AND PLACEMENT
The BETA 58A is designed for close-up vocals, and can be
hand held or mounted on a stand. Some of the most common
applications and placement techniques are listed in the fol-
lowing table. Keep in mind that microphone technique is
largely a matter of personal taste—there is no one “correct”
microphone position.
SUGGESTED MICROPHONE
PLACEMENT
TONE QUALITY
Lips less than 15 cm (6 in.) away Robust sound, emphasized
or touching the windscreen, on bass, maximum isolation from
axis to microphone.
other sources.
15 to 60 cm (6 in. to 2 ft.) away Natural sound, reduced bass.
from mouth, just above nose
height.
20 to 60 cm (8 in. to 2 ft.) away Natural sound, reduced bass
from mouth, slightly off to one and minimal ”s” sounds.
side.
90 cm to 1.8 m (3 to 6 ft.) away. Thinner, distant sound; notice-
able levels of ambient noise.
GENERAL RULES FOR MICROPHONE USE
1. Aim the microphone toward the desired sound source and
away from unwanted sources. Since supercardioid micro-
phones such as the BETA 58A have narrow pickup pat-
terns and can pick up sounds from the rear, this may not
be obvious or intuitive.
2. Place the microphone as close as practical to the desired
sound source. Refer to the table above.
3. Work close to the microphone for extra bass response.
4. Use only one microphone to pick up one sound source.
5. Keep the distance between microphones at least three
times the distance from each source to its microphone.
6. Use the fewest number of microphones as is practical.
7. Place microphones as far as possible from reflective sur-
faces.
8. Add a windscreen when using the microphone outdoors.
9. Avoid excessive handling to minimize pickup of mechani-
cal noise and vibration.
10. Do not cover any part of the grille with your hand.
PROXIMITY EFFECT
Unidirectional microphones such as the BETA 58A progres-
sively boost bass frequencies by 6 to 10 dB at 100 Hz when
the microphone is at a distance of about 6 mm (1/4 in.) from
the sound source. This phenomenon, known as proximity ef-
fect, can be used to create a warmer, more powerful sound.
To prevent explosive low frequency sound during close–up
use, the BETA 58A bass response gradually rolls off. This pro-
vides greater control and helps the user take advantage of
proximity effect.
Printed in U.S.A.






BETA58A Datasheet, Funktion
AUFSTELLUNG DER BÜHNENLAUTSPRECHER UND
LAUTSPRECHER FÜR BESCHALLUNGSANLAGEN
Zur maximalen Unterdrückung unerwünschter Töne den
bzw. die Bühnenlautsprecher oder den bzw. die Lautsprecher
der Beschallungsanlage in einem Winkel von 60_ zur Rücksei-
te des BETA 58A, nicht direkt dahinter aufstellen (siehe Abbil-
dung 1). Vor einem Auftritt stets die Bühnenausstattung über-
prüfen, um sicherzustellen, daß die Aufstellung des
Mikrophons und der Bühnenlautsprecher optimal ist.
BÜHNENLAUTSPRECHER
180°
120°
90°
LAUTSPRECHER DER
BESCHALLUNGSANLAGE
120°
Ausgangspegel (bei 1000 Hz)
Leerlaufspannung: –51,5 dBV/Pa* (2,6 mV)
*1 Pa = 94 dB SPL
Impedanz
Die Nennimpedanz für den Anschluß an niederohmige Mi-
krophoneingänge beträgt 150 W (Ist–Wert 290 W)
Phasenabgleich
Positiver Druck auf die Membran erzeugt positive Span-
nung an Stift 2 gegenüber Stift 3. Siehe Abbildung 4.
BLAU
GRÜN
ROT
GELB
www.DataSheet4U.com
0°
EMPFOHLENE LAUTSPRECHERSTELLUNGEN
ABBILDUNG 1
SPEZIFIKATIONEN
Typ
Dynamisch (Tauchspule)
Frequenzverhalten
5–+011ÁÁÁÁÁÁÁ000bisÁÁÁÁÁÁ523015.1m6mmmmmm6ÁÁÁÁÁÁÁ.000ÁÁÁÁÁÁÁHzÁÁÁÁÁÁÁ(sieÁÁÁÁÁÁÁheÁÁÁÁÁÁÁAbbÁÁÁÁÁÁÁilduÁÁÁÁÁÁÁngÁÁÁÁÁÁÁ2) ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
20
50 100 200
500
1,000
2,000
5,000
10,000 20,000
FREQUENZ IN HZ
TYPISCHES FREQUENZVERHALTEN
ABBILDUNG 2
HINWEIS: Die Kurve unten zeigt ein axiales Verhalten in
einem Abstand von 0,6 m von einer gleichförmigen Ton-
quelle. Das Frequenzverhalten ist von der Mikrophonstel-
lung abhängig.
Polarcharakteristik
Supernierencharakteristik, rotationssymmetrisch um Mikro-
phonachse, gleichförmig mit Frequenz (siehe Abbildung 3)
INTERNE SCHALTUNGEN
ABBILDUNG 4
Gehäuse
Silberblaues einbrennlackiertes Druckgußmetall mit ge-
härtetem, kugelförmigem Stahlgittergrill in matter Oberflä-
chenausführung
Verstellbarer, einrastender Stativadapter
Gleitverbindung, bruchbeständig, durch 180_ verstellbar
mit 5/8”–27 Standardgewinde, schwarze Oberflächenaus-
führung
Dimensions (siehe Abbildung 5)
50 mm
160 mm
Nettogewicht
278 Gramm
GESAMTABMESSUNGEN
ABBILDUNG 5
Zulassung
Zur CE–Kennzeichnung berechtigt. Entspricht der EU–
Richtlinie über elektromagnetische Verträglichkeit
89/336/EEC. Erfüllt die Prüfungs– und Leistungskriterien
der europäischen Norm EN 55103 (1996) Teil 1 und 2 für
Wohngebiete (E1) und Leichtindustriegebiete (E2).
150o
120o
180o
150o
120o
150o
120o
180o
150o
120o
90o
60o
–20 dB
90o 90o
–20 dB
–15 dB
–15 dB
–10 dB
60o 60o
–10 dB
–5 dB
–5 dB
30o 30o
0
250 Hz
500 Hz
1000 Hz
30o 30o
0
2500 Hz
6300 Hz
10000 Hz
TYPISCHE POLARCHARAKTERISTIK
ABBILDUNG 3
90o
60o
MITGELIEFERTES ZUBEHÖR
Verstellbarer, einrastender Stativadapter . . . . . . . . . A25D
5/8 zu 3/8 Inch (Euro) Gewindeadapter . . . . . . . . 95A2050
Tasche . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26A21
SONDERZUBEHÖR
Windschirm . . . . . . . . A58WS Serie (in 8 Farben erhältlich)
Isolierbefestigung . . . . . . . . . . . . . . . . . . . . . A55M, A55HM
Kabel, 7,6 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . C25E, C25F
ERSATZTEILE
Kapsel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . R176
Grill–Baugruppe . . . . . . . . . . . . . . . . . . . . . . . . . . . . RK265G
Stecker– (Anschluß–) Baugruppe . . . . . . . . . . . . 90F1984
6

6 Page









BETA58A pdf, datenblatt
www.DataSheet4U.com
SHURE Incorporated Web Address: http://www.shure.com
5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.
Phone: 800-257-4873 Fax: 847-600-1212
In Europe, Phone: 49-7131-72140 Fax: 49-7131-721414
In Asia, Phone: 852-2893-4290 Fax: 852-2893-4055
Elsewhere, Phone: 847-600-2000 Fax: 847-600-6336

12 Page





SeitenGesamt 12 Seiten
PDF Download[ BETA58A Schematic.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
BETA58AMicrophoneShure
Shure
BETA58AMicrophone user guideShure
Shure

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com       |      2020       |      Kontakt     |      Suche