|
|
Número de pieza | VM-1201 | |
Descripción | Service Manual | |
Fabricantes | Speco | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de VM-1201 (archivo pdf) en la parte inferior de esta página. Total 16 Páginas | ||
No Preview Available ! www.DataSheet4U.com
SERVICE MANUAL
MODEL
: VM-1201
REVISION
: A0
DATE
: MAY. 21. 2001
DOCUMENT NUMBER :
1 page www.DataSheet4U.com
1.1.2 Signal Input Requirements
‧ Connector
For CVBS:BNC terminal
Type:composite video input Level:1.0Vp-p
Synchronous:0.3 V
Luminance:0.7V
Polarity:Positive bright
Impedance:75 ohms
1.1.3 Power Input Requirements
‧ Operating Voltage Range:90 ~ 264 VAC at 50 / 60 ±3Hz
‧ Input Current at 90 VAC
Operating:0.5 Amps rms. maximum
‧ Input Current at 264 V
Operating:0.3 Amps rms. maximum
‧ Power consumption
Normal operation:30 Watts maximum
1.2 Functional Specification
The standard conditions for verifying the following specification are as below:
4
5 Page www.DataSheet4U.com
• Flyback generator:
‧ U301 pin6 is the output of the flyback generator that when driven, jumps from low to high
condition C305 transfers the jump to pin3
• Vertical size control:VR301, R312, R308.
2.5 Horizontal Deflection Block
• Horizontal drive buffering:Driving source-U401 pin11. Driving transistor-Q40, to pull high the
driving waveform to drive the Q401(MOS FET).
• Horizontal deflection:Horizontal Output transistor-Q401; Load-Yoke inductance and C414 ;
D401, High Voltage generation-flyback transformer .
3 Troubleshooting Instructions
‧ This chapter describes possible failures of the monitor with corresponding check/correction
actions, and guidelines for safe operation and service of the monitor.
3.1No Display, No Power
3.1.1First of all, turn power off, use multimeter to check Q901, and R904, replace if bad. Turn
power on after that.
3.1.2Check DC voltage across C906. If no voltage or voltage too low, check and fix the following
components:AC receptacle poor contact, fuse F601 broken, power switch malfunction, or
bridge diode D901 bad
3.1.3Check voltage on U901 pin 7 for start up condition:If voltage on U901 pin 7 reaches the start
up voltage(around 15 to 17.5V), U901 UC3842 will start to work and output 5V at pin 8. If
voltage on U601 pin 7 is too low, check and fix following circuits:start up circuit R914,
and C914.
3.1.4If no output pulses at U901 pin 6, check and replace U901.
10
11 Page |
Páginas | Total 16 Páginas | |
PDF Descargar | [ Datasheet VM-1201.PDF ] |
Número de pieza | Descripción | Fabricantes |
VM-1201 | Service Manual | Speco |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |