|
|
PDF CMX-3000 Data sheet ( Hoja de datos )
| Número de pieza | CMX-3000 | |
| Descripción | CD Player | |
| Fabricantes | Pioneer | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de CMX-3000 (archivo pdf) en la parte inferior de esta página. Total 20 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
COMPACT DISC PLAYER
CMX-3000
Operating Instructions
1 page  
www.DataSheet4U.com
Read before use
Cleaning and handling compact discs
÷ The presence of fingerprints or smudges on the surface of
the disc will not directly affect the recorded signals, but,
depending on the degree of contamination, the brightness of
the light reflected from the signal surfaces may be reduced
causing degradation of sound quality. Always keep your discs
clean by wiping them gently with a soft cloth from the inner
edge toward the outer edge.
÷ If a disc becomes very dirty, dampen a soft cloth with water,
(be sure to wring it out well) and wipe the away dirt gently.
Remove any water drops with another soft, dry cloth.
÷ Do not use record cleaning sprays or anti-static agents on
discs. Never clean discs with benzene, thinner, or other
volatile solvents or damage to the disc surface may result.
÷ With this player, use only those
discs which display the mark
shown right (Optical audio digital
discs).
'
÷ When holding discs, do not touch their signal surfaces. Hold
by the edges, or by one edge and the center hole.
÷ Do not affix gummed labels or tape to the disc surface. Also,
do not scratch or damage the label.
÷ Discs rotate at high speeds inside the player. Do not use
damaged, cracked or warped discs.
FORCED DISC EJECTION
If the EJECT button fails to work and it becomes impossible
to eject a disc, the disc may be ejected by inserting the disc
ejection pin in the manual disc ejection hole located on the
front panel of the player.
Always be sure to observe the following points when
manually ejecting discs.
1 Be sure to turn off the power to the CD player and wait
for 1 minute or more before ejecting the disc.
Manually ejecting a disc immediately after the
power to the unit has been turned off may
result in one of the following problems from
occurring, and care should accordingly be
taken never to eject discs immediately after the
power has been turned off.
÷ The disc will still be spinning when it is ejected, thus
resulting in cuts to the fingers or other forms of bodily
injury.
÷ The disc clamps will spin in an unstable state, thus
resulting in scratching of discs.
2 Be sure to use only the disc ejection pin included with
your CMX-3000 (i.e., never use a paper clip or any other
object).
Inserting the disc ejection pin into the hole until it
encounters resistance will cause the disc to be ejected
some 5 to 10 millimeters from the insertion slot. The
disc may then be removed by grasping it by hand and
pulling.
Manual
disc ejection hole
Do not play a CD with a special shape
Do not play a CD having other shape than a circular disc, such as
heart shaped disc. Otherwise malfunction may occur.
<DRB1307> 5
5 Page 
www.DataSheet4U.com
Read before use (Connections)
B Connecting the CMX-3000 to stereo amplifiers (when not using a DJ mixer)
Stereo
amplifier
Connect audio cable to CD or AUX input jacks.
(Do not connect to PHONO input jacks.)
INPUT
CD
L
R
CMX-3000 audio cable
Player
C Connecting the CMX-3000 to devices with digital input jacks
CD recorder or other device with
digital input amplifier
DIGITAL INPUT
OPTICAL COAXIAL
Digital signal
cable
Player
¶ When using the digital output jacks, the DIGITAL MODE switch must be set to ‘ON’.
Note:
Turning the DIGITAL MODE switch ‘ON’ causes all DJ features (i.e., CUE, LOOP, RELOOP, TEMPO CONTROL, MASTER
TEMPO, increase/reduce speed by the jog dial or HOT CUE) to be disabled. Also note that when using digital output pausing
results not in a start playback pause but in a silent pause instead.
4. Connecting the power cord
When all connections have been made, connect the power cord to the AC inlet on the rear panel of the player and connect the power
plug to an AC wall outlet or to a power receptacle on the rear panel of the amplifier.
DISC LOADING/UNLOADING
Label surface up
Insert straight
POWER switch
1. Press POWER switch on front of player to turn power
on.
Do not force a disc into the unit when the POWER switch is set
to OFF as this may damage the disc and the unit.
2. Insert a disc.
¶ Hold the disc with label surface upwards, and insert into the
front panel disc insertion slot .
¶ When playing an 3 inch/8 cm disc, place the disc in a
commercially available CD adapter before inserting in the
insertion slot.
¶ Each insertion slot can only accommodate one disc at a time.
Never attempt to load more than one disc at the same time,
or attempt to load a second disc when one disc has already
been loaded.
¶ When loading a disc, do not placing any twisting force on the
disc, or try to force the disc into the slot. Also, do not attempt
to interrupt or defeat the motion of the disc when the player
begins to draw a disc into the slot or to eject a disc, since
damage to the disc or player could occur.
3. During playback, press the PLAY/PAUSE button
(38) or if a cue point has been specified press the
CUE button to back-cue before pressing the EJECT
button (0) to eject a disc
¶ When the EJECT button is pressed, disc rotation stops and
the disc is ejected from the loading slot.
¶ If the disc fails to be ejected when the EJECT button is
pressed, the accessory forced eject pin can be inserted into
the front-panel’s forced eject hole to eject the disc. (see p. 5)
CAUTION:
Do not attempt to press a disc back into the slot when the EJECT
indicator appears. Pressing a disc back into the slot while the
EJECT indicator appears may cause the player to stop. In this case,
press the EJECT button again and wait until the EJECT indicator
goes out before reinserting the disc.
<DRB1307> 11
11 Page | ||
| Páginas | Total 20 Páginas | |
| PDF Descargar | [ Datasheet CMX-3000.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| CMX-3000 | CD Player | Pioneer |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |