Datenblatt-pdf.com


AZ10LVE111E Schematic ( PDF Datasheet ) - Arizona Microtek

Teilenummer AZ10LVE111E
Beschreibung ECL/PECL 1:9 Differential Clock Driver
Hersteller Arizona Microtek
Logo Arizona Microtek Logo 




Gesamt 6 Seiten
AZ10LVE111E Datasheet, Funktion
www.DataSheet4U.com
ARIZONA MICROTEK, INC.
AZ10LVE111E
AZ100LVE111E
ECL/PECL 1:9 Differential Clock Driver with Enable
FEATURES
PACKAGE AVAILABILITY
Operating Range of 3.0V to 5.5V
Low Skew
Guaranteed Skew Spec
PACKAGE
PLCC 28
PART NO.
AZ10LVE111EFN
MARKING
AZ10
LVE111E
<Date Code>
NOTES
1,2
Differential Design
AZ100
Enable
PLCC 28
AZ100LVE111EFN LVE111E
1,2
VBB Output
75kΩ Internal Input Pulldown Resistors
<Date Code>
1 Add R2 at end of part number for 13 inch (750 parts) Tape & Reel.
2 Date code format: “YY” for year followed by “WW” for week.
Direct Replacement for ON Semiconductor
MC10E111 & MC100E111
DESCRIPTION
The AZ10/100LVE111E is a low skew 1-to-9 differential driver, designed with clock distribution in mind. The
IN signal is fanned-out to nine identical differential outputs. An Enable input is also provided. A HIGH disables the
device by forcing all Q outputs LOW and all Q¯ outputs HIGH.
The AZ100LVE111E provides a VBB output for single-ended use or a DC bias reference for AC coupling to the
device. For single–ended input applications, the VBB reference should be connected to one side of the IN/I¯N¯
differential input pair. The input signal is then fed to the other IN/I¯N¯ input. The VBB pin should be used only as a
bias for the AZ100LVE111E as its current sink/source capability is limited. When used, the VBB pin should be
bypassed to ground via a 0.01μF capacitor.
The device is specifically designed, modeled and produced with low skew as the key goal. Optimal design and
layout serve to minimize gate-to-gate within-device skew, and empirical modeling is used to determine process
control limits that ensure consistent tpd distributions from lot-to-lot. The net result is a dependable, guaranteed low
skew device.
To ensure that the tight skew specification is met, both sides of the differential output must be terminated into
50Ω, even if only one side is used. In most applications all nine differential pairs will be used and therefore
terminated. In the case where fewer than nine pairs are used, it is necessary to terminate at least the output pairs on
the same package side (i.e. sharing the same VCCO) as the pair(s) being used on that side, in order to maintain
minimum skew. Failure to do this will result in small degradations of propagation delay (on the order of 10-20ps) of
the output(s) being used that, while not being catastrophic to most designs, will mean a loss of skew margin.
NOTE: Specifications in the ECL/PECL tables are valid when thermal equilibrium is established.
1630 S. STAPLEY DR., SUITE 127 MESA, ARIZONA 85204 USA (480) 962-5881 FAX (480) 890-2541
www.azmicrotek.com






AZ10LVE111E Datasheet, Funktion
AZ10LVE111E
AZ100LVE111E
Arizona Microtek, Inc. reserves the right to change circuitry and specifications at any time without prior notice. Arizona Microtek, Inc.
makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Arizona
Microtek, Inc. assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all
liability, including without limitation special, consequential or incidental damages. Arizona Microtek, Inc. does not convey any license
rights nor the rights of others. Arizona Microtek, Inc. products are not designed, intended or authorized for use as components in systems
intended to support or sustain life, or for any other application in which the failure of the Arizona Microtek, Inc. product could create a
situation where personal injury or death may occur. Should Buyer purchase or use Arizona Microtek, Inc. products for any such
unintended or unauthorized application, Buyer shall indemnify and hold Arizona Microtek, Inc. and its officers, employees, subsidiaries,
affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly
or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Arizona Microtek, Inc. was negligent regarding the design or manufacture of the part.
November 2006 * REV - 4
www.azmicrotek.com
6

6 Page







SeitenGesamt 6 Seiten
PDF Download[ AZ10LVE111E Schematic.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
AZ10LVE111ECL/PECL 1:9 Differential Clock DriverArizona Microtek
Arizona Microtek
AZ10LVE111ECL/PECL 1:9 Differential Clock DriverArizona Microtek
Arizona Microtek
AZ10LVE111EECL/PECL 1:9 Differential Clock DriverArizona Microtek
Arizona Microtek
AZ10LVE111EECL/PECL 1:9 Differential Clock DriverArizona Microtek
Arizona Microtek

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com       |      2020       |      Kontakt     |      Suche