|
|
PDF ISL14011 Data sheet ( Hoja de datos )
| Número de pieza | ISL14011 | |
| Descripción | Low Jitter Clock Generators | |
| Fabricantes | Intersil Corporation | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de ISL14011 (archivo pdf) en la parte inferior de esta página. Total 5 Páginas | ||
|
No Preview Available !
®
Data Sheet
January 30, 2007
ISL14011
FN6427.0
Low Jitter Clock Generators for Set-Top
Box
The ISL14011 series of devices are general purpose
integrated Clock Synthesizers and Generators suited for
consumer applications such as Set-top Box, and various
other consumer applications.
The selectable reference input accepts 30MHz signal either
from crystal or an external source. It is specified to operate
with a nominal 3.3V supply and is offered in 16 Ld QFN
package.
Contact Factory for other output frequency options.
Ordering Information
PART
NUMBER
PART
TEMP.
PKG.
MARKING RANGE (°C) PACKAGE DWG. #
ISL14011IRZ* 11IZ
-40 to +85 16 Ld QFN L16.3x3
*Add "-T" suffix for tape and reel.
NOTE: Intersil Pb-free plus anneal products employ special Pb-free
material sets; molding compounds/die attach materials and 100% matte
tin plate termination finish, which are RoHS compliant and compatible
with both SnPb and Pb-free soldering operations. Intersil Pb-free
products are MSL classified at Pb-free peak reflow temperatures that
www.DataSheet4U.comm eet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
Selection Table
NUMBER
PART
INPUT
OF OUTPUT
OPTIONS FREQUENCY OUTPUTS FREQUENCY PACKAGE
ISL14011
30MHz
4 LVTTL 25, 30, 24, 27 16 Ld QFN
Features
• LVTTL Outputs
• Selectable Crystal or Ref. Clock for Inputs
• Period Jitter ~50ps RMS
• Single Supply; 3.3V nominal
• Extended Temperature Range: -40°C to +85°C
• Available in small foot print package
- 16 Ld QFN 3mmx3mm
• Pb-Free plus anneal available (RoHS Compliant)
Applications
• Set-Top Boxes
Pinout
ISL14011
(16 LD QFN)
TOP VIEW
16 15 14 13
VCC 1
X1 2
X2 3
GND 4
12 NC
11 CLK3
10 CLK2
9 NC
5678
1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2007. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
1 page  
ISL14011
Quad Flat No-Lead Plastic Package (QFN)
Micro Lead Frame Plastic Package (MLFP)
2X
AD
0.15 C A
9 D/2
6
INDEX
AREA
1
2
3
D1
D1/2
N
2X
0.15 C B
2X
0.15 C A
TOP VIEW
2X
0.15 C B
E1/2 E/2
E1 E
9
B
4X
C
A2
A / / 0.10 C
0.08 C
SEATING PLANE SIDE VIEW
A3 A1
9
4X P
(DATUM B)
4X P
(DATUM A)
6
INDEX
AREA
NX L
8
NX b 5
0.10 M C A B
D2 7 8
D2
2N
NX k
1
2
3
(Ne-1)Xe
E2 REF.
7
E2/2
8
Ne
(Nd-1)Xe
REF.
BOTTOM VIEW
9
CORNER
OPTION 4X
NX b
5
A1
SECTION "C-C"
CL CL
L
L1 10
L
L1 10
e
CC
TERMINAL TIP
e
FOR ODD TERMINAL/SIDE
FOR EVEN TERMINAL/SIDE
L16.3x3
16 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE
MILLIMETERS
SYMBOL
A
MIN
0.80
NOMINAL
0.90
MAX
1.00
NOTES
-
A1 -
- 0.05 -
A2 -
- 1.00 9
A3 0.20 REF 9
b 0.18 0.23 0.30 5, 8
D
3.00 BSC
-
D1 2.75 BSC 9
D2 1.35 1.50 1.65 7, 8, 10
E
3.00 BSC
-
E1 2.75 BSC 9
E2 1.35 1.50 1.65 7, 8, 10
e
0.50 BSC
-
k 0.20
-
--
L 0.30 0.40 0.50 8
N 16 2
Nd 4 3
Ne 4 3
P-
θ-
- 0.60 9
- 12 9
Rev. 1 6/04
NOTES:
1. Dimensioning and tolerancing conform to ASME Y14.5-1994.
2. N is the number of terminals.
3. Nd and Ne refer to the number of terminals on each D and E.
4. All dimensions are in millimeters. Angles are in degrees.
5. Dimension b applies to the metallized terminal and is measured
between 0.15mm and 0.30mm from the terminal tip.
6. The configuration of the pin #1 identifier is optional, but must be
located within the zone indicated. The pin #1 identifier may be
either a mold or mark feature.
7. Dimensions D2 and E2 are for the exposed pads which provide
improved electrical and thermal performance.
8. Nominal dimensions are provided to assist with PCB Land
Pattern Design efforts, see Intersil Technical Brief TB389.
9. Features and dimensions A2, A3, D1, E1, P & θ are present when
Anvil singulation method is used and not present for saw
singulation.
10. Compliant to JEDEC MO-220VEED-2 Issue C, except for the E2
and D2 MAX dimension.
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
5 FN6427.0
January 30, 2007
5 Page | ||
| Páginas | Total 5 Páginas | |
| PDF Descargar | [ Datasheet ISL14011.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| ISL14010 | (ISL14010 / ISL14017) Low Jitter Clock Generators | Intersil Corporation |
| ISL14011 | Low Jitter Clock Generators | Intersil Corporation |
| ISL14017 | (ISL14010 / ISL14017) Low Jitter Clock Generators | Intersil Corporation |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |