|
|
PDF MSK1695 Data sheet ( Hoja de datos )
| Número de pieza | MSK1695 | |
| Descripción | BRUSHLESS MOTOR SPEED CONTROLLER | |
| Fabricantes | MSK | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de MSK1695 (archivo pdf) en la parte inferior de esta página. Total 7 Páginas | ||
|
No Preview Available !
40 AMP, 34V, 3 PHASE
BRUSHLESS MOTOR
M.S.KENNEDY CORP.
SPEED CONTROLLER
4707 Dey Road Liverpool, N.Y. 13088
FEATURES:
34V Maximum Supply Voltage - +28V Nominal
40 Amps DC @ 70°C Case Temperature
Shoot-through, Cross Conduction Protection
Hall Sensing and Commutation Circuitry On Board
Pulse by Pulse 50 Amp Current Limit
EQUIVALENT SCHEMATIC
1695
(315) 701-6751
www.DataSheet4U.com
TYPICAL APPLICATIONS
Fan/Blower Speed Control
Azimuth/Elevation Antenna Control
Optical Tracking Control
Robot Velocity Control
PIN-OUT INFORMATION
PCB PADS
L1 A PHASE OUT
L2 B PHASE OUT
L3 C PHASE OUT
V+ +28V IN
VRTN +28V RTN
1
HEADER CONNECTION
1 BRAKE
2 60/120
3 HALL B
4 HALL C
5 GND
6 GND
7 GND
8 GND
9 +12V
10 FWD/REV
11 HALL A
12 VREF
13 SPEED COMMAND
14 GND
15 GND
PRELIMINARY Rev. B 11/06
1 page  
APPLICATION NOTES CONTINUED
BUS VOLTAGE FILTER CAPACITORS
The size and placement of the capacitors for the DC bus has a direct bearing on the amount of noise filtered and also on the size
and duration of the voltage spikes seen by the bridge. What is being created is a series RLC tuned circuit with a resonant
frequency that is seen as a damped ringing every time one of the transistors switches. For the resistance, wire resistance, power
supply impedance and capacitor ESR all add up for the equivalent lumped resistance in the circuit. The inductance can be figured
at about 30 nH per inch from the power supply. Any voltage spikes are on top of the bus voltage and the back EMF from the
motor. All this must be taken into account when designing and laying out the system. If everything has been minimized, there is
another solution. A second capacitance between 5 and 10 times the first capacitor and it should either have some ESR or a
resistor can be added in series with the second capacitor to help damp the voltage spikes.
Be careful of the ripple current in all the capacitors. Excessive ripple current, beyond what the capacitors can handle, will destroy
the capacitors.
LOW POWER STARTUP
When starting up a system utilizing the MSK 1695 for the first time, there are a few things to keep in mind. First, because of the
small size of the module, short circuiting the output phases either to ground or the DC bus will destroy the bridge. The current
limiting and control only works for current actually flowing through the bridge. The current limit sensor has to see the current in
order for the electronics to control it. If possible, for startup use a lower current power supply to test out connections and the low
current stability. With a limited current supply, even if the controller locks up, the dissipation will be limited.
5 PRELIMINARY Rev. B 11/06
5 Page | ||
| Páginas | Total 7 Páginas | |
| PDF Descargar | [ Datasheet MSK1695.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| MSK1695 | BRUSHLESS MOTOR SPEED CONTROLLER | MSK |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |