|
|
PDF MC10EP51 Data sheet ( Hoja de datos )
| Número de pieza | MC10EP51 | |
| Descripción | 3.3V / 5V ECL D Flip-Flop | |
| Fabricantes | ON Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de MC10EP51 (archivo pdf) en la parte inferior de esta página. Total 11 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
MC10EP51, MC100EP51
3.3V / 5V ECL D Flip−Flop
with Reset and Differential
Clock
Description
The MC10/100EP51 is a differential clock D flip−flop with reset.
The device is functionally equivalent to the EL51 and LVEL51
devices.
The reset input is an asynchronous, level triggered signal. Data
enters the master portion of the flip−flop when the clock is LOW and is
transferred to the slave, and thus the outputs, upon a positive transition
of the clock. The differential clock inputs of the EP51 allow the device
to be used as a negative edge triggered flip-flop.
The differential input employs clamp circuitry to maintain stability
under open input conditions. When left open, the CLK input will be
pulled down to VEE and the CLK input will be biased at VCC/2.
The 100 Series contains temperature compensation.
Features
• 350 ps Typical Propagation Delay
• Maximum Frequency > 3 GHz Typical
• PECL Mode Operating Range: VCC = 3.0 V to 5.5 V
with VEE = 0 V
• NECL Mode Operating Range: VCC = 0 V
with VEE = −3.0 V to −5.5 V
• Open Input Default State
• Safety Clamp on Inputs
• Pb−Free Packages are Available
http://onsemi.com
8
1
SOIC−8
D SUFFIX
CASE 751
MARKING DIAGRAMS*
8
HEP51
ALYW
G
1
8
KEP51
ALYW
G
1
8
1
TSSOP−8
DT SUFFIX
CASE 948R
8
HP51
ALYWG
G
1
8
KP51
ALYWG
G
1
DFN8
MN SUFFIX
CASE 506AA
14
14
H = MC10
A = Assembly Location
K = MC100
L = Wafer Lot
5S = MC10
Y = Year
3N = MC100
W = Work Week
M = Date Code G = Pb−Free Package
(Note: Microdot may be in either location)
*For additional marking information, refer to
Application Note AND8002/D.
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 8 of this data sheet.
© Semiconductor Components Industries, LLC, 2006
November, 2006 − Rev. 6
1
Publication Order Number:
MC10EP51/D
1 page  
MC10EP51, MC100EP51
Table 8. 100EP DC CHARACTERISTICS, PECL VCC = 3.3 V, VEE = 0 V (Note 11)
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
VOH
VOL
VIH
VIL
VIHCMR
Power Supply Current
Output HIGH Voltage (Note 12)
Output LOW Voltage (Note 12)
Input HIGH Voltage (Single−Ended)
Input LOW Voltage (Single−Ended)
Input HIGH Voltage Common Mode Range
(Differential Configuration) (Note 13)
26
2155
1355
2075
1355
2.0
34
2280
1480
44
2405
1605
2420
1675
3.3
26
2155
1355
2075
1355
2.0
35
2280
1480
45
2405
1605
2420
1675
3.3
28
2155
1355
2075
1355
2.0
37
2280
1480
47
2405
1605
2420
1675
3.3
mA
mV
mV
mV
mV
V
IIH Input HIGH Current
IIL Input LOW Current
150 150 150 mA
0.5 0.5 0.5 mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
11. Input and output parameters vary 1:1 with VCC. VEE can vary +0.3 V to −2.2 V.
12. All loading with 50 W to VCC − 2.0 V.
13. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal.
Table 9. 100EP DC CHARACTERISTICS, PECL VCC = 5.0 V, VEE = 0 V (Note 14)
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
VOH
VOL
VIH
VIL
VIHCMR
Power Supply Current
Output HIGH Voltage (Note 15)
Output LOW Voltage (Note 15)
Input HIGH Voltage (Single−Ended)
Input LOW Voltage (Single−Ended)
Input HIGH Voltage Common Mode Range
(Differential Configuration) (Note 16)
26
3855
3055
3775
3055
2.0
34
3980
3180
44
4105
3305
4120
3375
5.0
26
3855
3055
3775
3055
2.0
35
3980
3180
45
4105
3305
4120
3375
5.0
28
3855
3055
3775
3055
2.0
37
3980
3180
47
4105
3305
4120
3375
5.0
mA
mV
mV
mV
mV
V
IIH Input HIGH Current
IIL Input LOW Current
150 150 150 mA
0.5 0.5 0.5 mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
14. Input and output parameters vary 1:1 with VCC. VEE can vary +2.0 V to −0.5 V.
15. All loading with 50 W to VCC − 2.0 V.
16. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal.
http://onsemi.com
5
5 Page 
MC10EP51, MC100EP51
PACKAGE DIMENSIONS
DFN8
CASE 506AA−01
ISSUE D
1
D
PIN ONE
REFERENCE
2X
0.10 C
ÇÇÇÇÇÇÇÇÇÇÇÇ
2X
0.10 C
TOP VIEW
A
B
E
0.10 C
A
8 X 0.08 C
SEATING
PLANE
A1
e/2
1
8X L
SIDE VIEW (A3)
D2
4
e
C
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994 .
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.25 AND 0.30 MM FROM TERMINAL.
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
MILLIMETERS
DIM MIN MAX
A 0.80 1.00
A1 0.00 0.05
A3 0.20 REF
b 0.20 0.30
D 2.00 BSC
D2 1.10 1.30
E 2.00 BSC
E2 0.70 0.90
e 0.50 BSC
K 0.20 −−−
L 0.25 0.35
E2
K
8
5
8X b
0.10 C A B
0.05 C NOTE 3
BOTTOM VIEW
ECLinPS is a trademark of Semiconductor Components Industries, LLC (SCILLC).
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
11
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
MC10EP51/D
11 Page | ||
| Páginas | Total 11 Páginas | |
| PDF Descargar | [ Datasheet MC10EP51.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| MC10EP51 | 3.3V / 5V ECL D Flip-Flop | ON Semiconductor |
| MC10EP52 | 3.3V / 5V ECL Differential Data and Clock D Flip-Flop | ON Semiconductor |
| MC10EP56 | Dual Differential 2:1 Multiplexer | ON Semiconductor |
| MC10EP57 | 4:1 Differential Multiplexer | ON Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |