Datenblatt-pdf.com


T520AxxxMxxxA Schematic ( PDF Datasheet ) - Kemet

Teilenummer T520AxxxMxxxA
Beschreibung (T520 Series) Conductive Polymer Chip Capacitors
Hersteller Kemet
Logo Kemet Logo 




Gesamt 7 Seiten
T520AxxxMxxxA Datasheet, Funktion
CONDUCTIVE POLYMER CHIP CAPACITORSwww.DataSheet4U.com
T520 Series - KO Cap
FEATURES
Polymer Cathode Technology
Use Up to 80% of Rated Voltage (20% Derating)
Low ESR
for part types > 10 Volts
High Frequency Cap Retention
Capacitance 15 to 1000µF (±20%)
No-Ignition Failure Mode
Voltage 2V to 25V
Use Up to 90% of Rated Voltage (10% Derating) EIA Standard Case Sizes
for part types 10 Volts
100% Surge Current Tested
Halogen Free Epoxy
Operating Temperature -55ºC to +105ºC
100% Accelerated Steady State Aging
Self Healing Mechanism
Volumetrically Efficient
RoHS Compiant & Leadfree Terminations (see
www.kemet.com for lead transition)
OUTLINE DRAWING
CATHODE (-) END
VIEW
SIDE VIEW
ANODE (+) END
VIEW
BOTTOM VIEW
W
H
KT
EF
X SGS
A
L
DIMENSIONS - MILLIMETERS
Case Size
KEMET EIA
A 3216-18
T 3528-12
B 3528-21
C 6032-28
U 6032-15
W 7343-15
V 7343-20
D 7343-31
Y 7343-40
X 7343-43
L
3.2 ± 0.2
3.5 ± 0.2
3.5 ± 0.2
6.0 ± 0.3
6.0 ± 0.3
7.3 ± 0.3
7.3 ± 0.3
7.3 ± 0.3
7.3 ± 0.3
7.3 ± 0.3
W
1.6 ± 0.2
2.8 ± 0.2
2.8 ± 0.2
3.2 ± 0.3
3.2 ± 0.3
4.3 ± 0.3
4.3 ± 0.3
4.3 ± 0.3
4.3 ± 0.3
4.3 ± 0.3
H
1.6 ± 0.2
1.2 max
1.9 ± 0.2
2.5 ± 0.3
1.5 max
1.5 max
1.9 max
2.8 ± 0.3
4.0 max
4.0 ± 0.3
K ± 0.20
0.9
0.3
0.9
1.4
0.5
0.6
0.9
1.5
1.9
2.3
F ± 0.1
1.2
2.2
2.2
2.2
2.2
2.4
2.4
2.4
2.4
2.4
S ± 0.3
0.8
0.8
0.8
1.3
1.3
1.3
1.3
1.3
1.3
1.3
X(Ref)
0.10 ± 0.10
0.05
0.10 ± 0.10
0.10 ± 0.10
0.05
0.05
0.05
0.10 ± 0.10
0.10 ± 0.10
0.10 ± 0.10
T(Ref)
0.13
0.13
0.13
0.13
0.13
0.13
0.13
0.13
0.13
0.13
A(Min)
0.8
1.1
1.1
2.5
3.1
3.8
3.8
3.8
3.8
3.8
G(ref)
1.1
1.8
1.8
2.8
2.8
3.5
3.5
3.5
3.5
3.5
E(ref)
1.3
2.2
2.2
2.4
2.4
3.5
3.5
3.5
3.5
3.5
T520 ORDERING INFORMATION
Tantalum
Series
T520 - Low ESR Polymer
Case Size
A, T, B, C, V, W, D, Y, X
T 520 V 157 M 006 A S E015
ESR
Lead Material
T - 100% Tin (Sn) Plated
H - Tin/Lead (SnPb 5% Pb minimum)
*S - Not recommended for new design
Failure Rate
A - Not Applicable
Capacitance Picofarad Code
First two digits represent significant figures.
Third digit specifies number of zeros to follow.
*See www.kemet.com for Pb Free transition information.
Voltage
Capacitance Tolerance
M = ± 20%
T520 SERIES CONSTRUCTION
COMPONENT MARKING
KEMET
Organic
KO
Polarity (+)
Indicator
157
Picofarad
Code
6wwRVoawlttea.dDgeataSheet4UK.com KEMET ID
512
PWC
512 = 12th week of 2005
©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
*100% Tin
49






T520AxxxMxxxA Datasheet, Funktion
TANTALUM, CERAMIC AND
www.DataSheet4U.com
ALUMINUM CHIP CAPACITORS
Packaging Information
Performance Notes
1. Cover Tape Break Force: 1.0 Kg Minimum.
2. Cover Tape Peel Strength: The total peel strength of the cover tape from the carrier tape shall be:
Tape Width
Peel Strength
8 mm
0.1 Newton to 1.0 Newton (10g to 100g)
12 mm
0.1 Newton to 1.3 Newton (10g to 130g)
The direction of the pull shall be opposite the direction of the carrier tape travel. The pull angle of the carrier
tape shall be 165Њ to 180Њ from the plane of the carrier tape. During peeling, the carrier and/or cover tape
shall be pulled at a velocity of 300 ±10 mm/minute.
3. Reel Sizes: Molded tantalum capacitors are available on either 180 mm (7") reels (standard) or 330 mm (13")
reels (with C-7280). Note that 13reels are preferred.
4. Labeling: Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes.
Refer to EIA-556.
Embossed Carrier Tape Configuration: Figure 1
Tape Size
8 mm
and
12 mm
Tape Size
8 mm
Table 1 — EMBOSSED TAPE DIMENSIONS (Metric will govern)
Constant Dimensions — Millimeters (Inches)
D0 E P0 P2 T Max
1.5
+0.10 -0.0
(0.059
+0.004, -0.0)
1.75 ±0.10
(0.069 ±0.004)
4.0 ±0.10
(0.157 ±0.004)
2.0 ±0.05
(0.079 ±0.002)
0.600
(0.024)
Variable Dimensions — Millimeters (Inches)
Pitch
B1 Max. D1 Min.
Note 1 Note 2
F
P1 R Min.
Note 3
Single
(4 mm)
4.4
(0.173)
1.0 3.5 ±0.05
4.0 ±0.10 25.0
(0.039) (0.138 ±0.002) (0.157 ±0.004) (0.984)
T1 Max
0.100
(0.004)
T2 Max
2.5
W
8.0 ±0.30
A0B0K0
Note 4
(0.098) (.315 ±0.012)
12 mm
Double
(8 mm)
8.2
(0.323)
1.5 5.5 ±0.05
8.0 ±0.10 30.0 4.6 12.0 ±0.30
(0.059) (0.217 ±0.002) (0.315 ±0.004) (1.181) (0.181) (0.472 ±0.012)
NOTES
1. B1 dimension is a reference dimension for tape feeder clearance only.
2. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of
wwemwbo.sDsmaetnat Slochateioen ta4ndUh.ocleolomcation shall be applied independent of each other.
3. Tape with components shall pass around radius Rwithout damage (see sketch A). The minimum trailer length (Fig. 2) may require
additional length to provide R min. for 12 mm embossed tape for reels with hub diameters approaching N min. (Table 2)
4. The cavity defined by A0, B0, and K0 shall be configured to surround the part with sufficient clearance such that the chip does not pro-
trude beyond the sealing plane of the cover tape, the chip can be removed from the cavity in a vertical direction without mechanical
restriction, rotation of the chip is limited to 20 degrees maximum in all 3 planes, and lateral movement of the chip is restricted to 0.5 mm
maximum in the pocket (not applicable to vertical clearance.)
©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
93

6 Page







SeitenGesamt 7 Seiten
PDF Download[ T520AxxxMxxxA Schematic.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
T520AxxxMxxxA(T520 Series) Conductive Polymer Chip CapacitorsKemet
Kemet
T520AxxxMxxxA(T520xxxxxxxA * Exx) T520 Series Conductive Polymer CapacitorETC
ETC

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com       |      2020       |      Kontakt     |      Suche