|
|
PDF sx09q002_b Data sheet ( Hoja de datos )
| Número de pieza | sx09q002_b | |
| Descripción | LCD_Module | |
| Fabricantes | HITACHI | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de sx09q002_b (archivo pdf) en la parte inferior de esta página. Total 28 Páginas | ||
|
No Preview Available !
.com Aug. 03, 2001
t4U KAOHSIUNG HITACHI
e ELECTRONICS CO.,LTD
e P.O. BOX 26-27
h 2,13TH EAST ST. K.E.P.Z.
S KAOHSIUNG TAIWAN R.O.C.
ta TEL:(07) 8211101(10 LINE)
a FAX:(07) 821-5860
No. 7B64LTD-2123-1
w.D LIQUID CRYSTAL DISPLAY MODULE
ww TECHNICAL DATA
SX09Q002-B omC O N T E N T S
.cNo. ITEM
SHEET No.
PAGE
1 COVER
7B64LTD 2123 – SX09Q002-B-1
1-1/1
U2 RECORD OF REVISION
7B64LTD 2123 – SX09Q002-B-1
2-1/1
t43 MECHANICAL DATA
7B64LTD 2123 – SX09Q002-B-1
3-1/1
4 ABSOLUTE MAXIMUM RATINGS 7B64LTD 2123 – SX09Q002-B-1
4-1/1
e5 ELECTRICAL CHARACTERISTICS 7B64LTD 2123 – SX09Q002-B-1
5-1/2~5-2/2
e6 OPTICAL CHARACTERISTICS 7B64LTD 2123 – SX09Q002-B-1
6-1/3~6-3/3
h7 BLOCK DIAGRAM
7B64LTD 2123 – SX09Q002-B-1
7-1/1
S8 INTERFACE TIMING CHART
7B64LTD 2123 – SX09Q002-B-1
8-1/7~8-7/7
ta9 DIMENSIONAL OUTLINE
7B64LTD 2123 – SX09Q002-B-1
9-1/1
10 APPEARANCE STANDARD
7B64LTD 2123 – SX09Q002-B-1
10-1/4~10-4/4
a11 PRECAUTION IN DESIGN
7B64LTD 2123 – SX09Q002-B-1
11-1/3~11-3/3
.D12 DESIGNATION OF LOT MARK 7B64LTD 2123 – SX09Q002-B-1
12-1/2~12-2/2
13 PRECAUTION FOR USE
7B64LTD 2123 – SX09Q002-B-1
13-1/1
w(NOTE)
1. This document may, wholly or partially, be subject to change without notice.
w2. All rights are reserved ; No one is permitted to reproduce or duplicate, in any from, the whole or part
of this document without Hitachi’s permission.
w3. No one is permitted to reveal the contents of this document to any third parties without Hitachi’s
permission.
m4. Hitachi shall not be held responsible for any damage to the user that may result from accidents or
.coany other reasons during operation of the user’s unit according to this document, any previous
reports or oral discussions.
U5. Circuit drawings and other examples described herein are meant merely to indicate the characteristics
t4and performance of Hitachi’s products. Hitachi assumes no responsibility for any intellectual property
eeclaims or other problems that may result from applications based on the examples described herein.
h6. No license is granted by implication or otherwise under any patents or other rights of any third party
Sor Hitachi, Ltd.
ta7. LIFE SUPPORT APPLICATIONS : Hitachi’s products are not authorized for use in
www.DaLIFE SUPPORT SYSTEMS.
1 page  
5. ELECTRICAL CHARACTERISTICS
5.1 ELECTRICAL CHARACTERISTICS OF LCD
ITEM
SYMBOL
CONDITION
Power Supply Voltage
VDD
-
Contrast Adjustment
VCON
-
Voltage (Note 1)
Input Voltage for Logic
Circuits (Note 2)
VI
“H” level
“L” level
Power Supply Current
(Note 3)
IDD VDD-VSS=3.3V
Input Leak Current
Icon(Note4) Vcon=1~VDD
Iin(Note2) Vin=VDDorVSS
Contrast Adjustment
Ta= 5°C , φ=0°
Voltage
VCON
Ta=25°C , φ=0°
(Note 5)
Ta=40°C . φ=0°
Frame Frequency
(Note 6)
fFLM
-
MIN.
3.15
1
TYP.
3.30
-
MAX.
3.45
VDD
0.8VDD -
0-
VDD
0.2VDD
- (4) (8)
-
-
-
(1.6)
(1.3)
-
-
(2.1)
2.0
(1.7)
± 10
± 5.0
(2.5)
(2.4)
-
60 70 100
UNIT
V
V
V
mA
µA
V
Hz
(Note 1) The brightness will increase with decreasing contrast adjustment voltage.
(Note 2) DISP • OFF ,FLM ,CL1 ,CL2 ,D0~D7.
(Note 3) fFLM=70Hz Ta=25°C, Pattern used as display pattern : All white.
(Note 4) VCON
(Note 5) fFLM=70Hz , Duty=1/245
The Contrast Adjustment Voltage is specified as (2.0± 0.4)V under the
condition that optimum contrast is obtained by naked eyes with a “Q” test
pattern.
(Note 6) Please set the frame frequency so as to avoid flicker and ripples on the
display.
(Note 7) Some points for attention while setting driving condition of appliance
(1) Frame Frequency
Please set the frame frequency as the typical value (central vale) which
in CAS. According to the characteristic or response time of LC material,
that setting the frame frequency near the mininum value or under the
minimum value shown in CAS will cause a frame with moving
phenomenon.
(2) Setting value Vcon
Vcon, adjusted to get the best contrast ratio of LCD module, is adjusted
to be distributed within the tolerance +/-0.4V of central value in CAS
before LCD modules ship the factory.
The below items are recommended at customer side.
(i) When designing the appliance, please set the Vcon value as an
adjustable value.
(ii) And the Vcon value must be able to be adjusted to match most suitable
Vcon to get the best contrast ratio. A fixed Vcon value a little different
from the most suitable Vcon value of LCD module and causes a
misjudgment.
(iii) The Vcon adjustment(when D/A [Digital/Analogue] converter is used) is
recommended to be set as 50mV at most per step. That one step is
more than 50mV may cause the input value to be not able match the
most suitable value.
The characteristic of contrast ratio can not present absolutely.
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE
Aug.03.’01
7B64LTD2123- SX09Q002-B-1 PAGE 5-1/2
5 Page 
8 INTERFACE TIMING CHART
8.1 TIMING CRART
CL1
CL2
Dummy data
D7 R B
Y1 Y9
D6 G R
Y2 Y10
D1 R B
Y7 Y15
D0 G R
Y8 Y16
30ns min.
FLM
(Reduction)
CL1
245 xT
FLM
T
X1
G
Y953
B
Y954
G
Y959
B
Y960
30ns min.
X2
D0~D7
X1 X2
X239 X240 Dummy data
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE
Aug.03.’01
7B64LTD2123- SX09Q002-B-1 PAGE 8-1/7
11 Page | ||
| Páginas | Total 28 Páginas | |
| PDF Descargar | [ Datasheet sx09q002_b.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| sx09q002_b | LCD_Module | HITACHI |
| sx09q002_bza | LCD_Module | HITACHI |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |