DataSheet.es    


PDF APAXT13U1 Data sheet ( Hoja de datos )

Número de pieza APAXT13U1
Descripción LCD_Module
Fabricantes UNIPAC 
Logotipo UNIPAC Logotipo



Hay una vista previa y un enlace de descarga de APAXT13U1 (archivo pdf) en la parte inferior de esta página.


Total 20 Páginas

No Preview Available ! APAXT13U1 Hoja de datos, Descripción, Manual

www.DataSShLePet4CEU.cDoCm IMFIOCDAUTLIOEN
U.comProducts Name:APAX T13U1
t413.3 INCH (1024x768)
eeCOLOR TFT LCD MODULE
h3.3V
.DataSl Preliminary Specification
wwwThis technical specification is tentative and it will be changed without notice.
eet4U.com76 39 4
ShTel:02-87912868 Fax:02-87912869
www.DataVersion. 1.0

1 page




APAXT13U1 pdf
SPEC NO. : 413-212-081
PA G E
: 3/16
BB.. EElleeccttrriiccaall ssppeecciiffiiccaattiioonnss
1.Pin assignment
(1).Input signal interface
CN1 (20P) connector : DF-19K-20P-1H(Hirose)
User’s matching connector : DF19G-20S-1C(Wire type)
DF19-20S-1F(FPC type)
Pin no
Symbol
Function
1 VCC +3.3 V power supply
2 VCC +3.3 V power supply
3
GND
Ground
4
GND
Ground
5
RxIN0-
LVDS receiver signal channel 0
6 RxIN0+
7
GND
Ground
8
RxIN1-
LVDS receiver signal channel 1
9 RxIN1+
10
GND
Ground
11
RxIN2-
LVDS receiver signal channel 2
12 RxIN2+
13
GND
Ground
14
CKIN-
LVDS receiver signal clock
15 CKIN+
16
GND
Ground
17 NC No Connection
18 NC No Connection
19
GND
Ground
20
GND
Ground
Etc.
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PRPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM UNIPAC OPTOELECTRONICS CORP.

5 Page





APAXT13U1 arduino
SPEC NO. :413-212-081
PA G E
: 9/16
e. Backlight driving conditions
Parameter
Symbol
Min.
Typ.
Max.
Unit
Remark
Lamp voltage
Lamp current
Power consumption
Lamp starting voltage
VL
IL
PL
VS
549 610 671 Vrms IL = 6mA
2 5 6.5 mArms Note 1
3.66
W Note 2
- - 1530
T=0

Vrms
- - 925
T=25

Frequency
FL 50 60 80 KHZ Note 3
Lamp life time
LL 10000
-
- Hr Note 4
Note 1: Using the inverter of PWM type(keep stable peak value of output voltage during
adjusting lamp current), the minimum lamp current is 2mA.
Note 2: Inverter should be designed with the characteristic of lamp. When you are designing
the inverter, the output voltage of the inverter should comply with the following
conditions.
(1).The area under the positive and negative cycles of the waveform of the lamp
current and lamp voltage should be area symmetric(the symmetric ratio should be
larger than 90%).
(2).There should not have any spikes in the waveform.
(3).The waveform should be sine wave as possible.
(4).Lamp current should not exceed the maximum value within the operating
temperature (It is prohibited to over the maximum lamp current even if operated in
the non-guaranteed temperature). When lamp current over the maximum value for
a long time, it may cause fire. Therefore, it is recommend that the inverter should
have the current limited circuit.
Note 3: Lamp frequency may produce interference with horizontal synchronous frequency and
this may cause line flow on the display. Therefore lamp frequency shall be detached
from the horizontal synchronous frequency and its harmonics as far as possible in
order to avoid interference. In case using the inverter by PWM control, PWM
frequency may interference with frame frequency. We suggest that PWM frequency
is same as frame frequency.
Note 4: T= 25

, IL = 6mA. Brightness to be decrease to the 50% of the initial value.
Note 5: CN2 connector(backlight): BHSR-02VS-1(JST).
Mating connector: SM02B-BHSS-1-TB (JST).
Pin no.
1
2
Symbol
H
L
Function
CCFL power supply(H.V.)
CCFL power supply(GND)
Remark
Cable color: Pink
Cable color: White
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PRPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM UNIPAC OPTOELECTRONICS CORP.

11 Page







PáginasTotal 20 Páginas
PDF Descargar[ Datasheet APAXT13U1.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
APAXT13U1LCD_ModuleUNIPAC
UNIPAC

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar