|
|
Teilenummer | UB104S01-2 |
|
Beschreibung | TFT LCD TOUCH PANEL | |
Hersteller | DATAMODUL | |
Logo | ||
Gesamt 19 Seiten www.DataSheet4U.com
.comSpecification
t4UUB104S01-2
hee10.4" (800 x 600) SVGA
ataSColor TFT with Touch
www.D .DataSheet4U.comDATA MODUL INC. - 1767-46 Veterans Memorial Highway - Islandia NY 11749 - Tel. 631-951-0800 - Fax 631-951-2121
wwwinfo@datamodul.com - www.datamodul.com
B. Electrical specifications
1.Pin assignment
(1).Input signal interface
Pin no
Symbol
Function
1 VCC +3.3 V power supply
2 VCC +3.3 V power supply
3
GND
Ground
4
GND
Ground
5
RxIN0-
LVDS receiver signal channel 0
6 RxIN0+
7
GND
Ground
8
RxIN1-
LVDS receiver signal channel 1
9 RxIN1+
10
GND
Ground
11
RxIN2-
LVDS receiver signal channel 2
12 RxIN2+
13
GND
Ground
14
CKIN-
LVDS receiver signal clock
15 CKIN+
16
GND
Ground
17 NC No Connection
18 NC No Connection
19
GND
Ground
20
GND
Ground
CN1 (20P) connector: HRS DF 19K-20P-1H or Compatible
3 /16
Etc.
DATA MODUL INC. - 1767-46 Veterans Memorial Highway - Islandia NY 11749 - Tel. 631-951-0800 - Fax 631-951-2121 - www.datamodul.com
6 Page Lamp life time
LL
10000
20000
-
9 /16
Hr Note 1, 5
Note 1: T= 25• IL=4.5mA
Note 2: Inverter should be designed with the characteristic of lamp. When you are designing
the inverter, the output voltage of the inverter should comply with the following
conditions.
(1). The area under the positive and negative cycles of the waveform of the lamp
current and lamp voltage should be area symmetric(the symmetric ratio should
be larger than 90%).
(2). There should not be any spikes in the waveform.
(3). The waveform should be sine wave as possible.
(4). Lamp current should not exceed the maximum value within the operating
temperature (It is prohibited to over the maximum lamp current even if operated
in the non-guaranteed temperature). When lamp current over the maximum
value for a long time, it may cause fire. Therefore, it is recommend that the
inverter should have the current limit circuit.
Note 3: The inverter open voltage should be designed larger than the lamp starting voltage
otherwise backlight may be blinking for a moment after turning on or not be able to
turn on. The open voltage should be measured after ballast capacitor. If an inverter
has shutdown function it should keep its open voltage for longer than 1 second
even if lamp connector is open.
Note 4: Lamp frequency may produce interference with horizontal synchronous frequency
and this may cause line flow on the display. Therefore lamp frequency
shall be detached from the horizontal synchronous frequency and its harmonics as
far as possible in order to avoid interference.
Note 5: Brightness (IL=4.5mA) to be decrease to the 50% of the initial value.
Note 6: CN2 connector (backlight): BHSR-02VS-1(JST)
Mating connector: SM02B-BHSS-1-TB (JST)
Pin no.
1
2
Symbol
H
L
Function
CCFL power supply(H.V.)
CCFL power supply(GND)
Remark
Cable color: Pink
Cable color: White
DATA MODUL INC. - 1767-46 Veterans Memorial Highway - Islandia NY 11749 - Tel. 631-951-0800 - Fax 631-951-2121 - www.datamodul.com
12 Page | ||
Seiten | Gesamt 19 Seiten | |
PDF Download | [ UB104S01-2 Schematic.PDF ] |
Teilenummer | Beschreibung | Hersteller |
UB104S01-2 | TFT LCD TOUCH PANEL | DATAMODUL |
UB104S01-V1 | LCD Module | DATAMODUL |
UB104S01-V3 | LCD Module | DATAMODUL |
Teilenummer | Beschreibung | Hersteller |
CD40175BC | Hex D-Type Flip-Flop / Quad D-Type Flip-Flop. |
Fairchild Semiconductor |
KTD1146 | EPITAXIAL PLANAR NPN TRANSISTOR. |
KEC |
www.Datenblatt-PDF.com | 2020 | Kontakt | Suche |