|
|
Teilenummer | PQ030EZ01Z |
|
Beschreibung | (PQ018EZ01Z / PQ025EZ01Z / PQ030EZ01Z / PQ033EZ01Z) DEVICE SPECIFICATION FOR VOLTAGE REGULATOR | |
Hersteller | Sharp Electrionic Components | |
Logo | ||
Gesamt 19 Seiten SHARP
ELECTRONIC COMPONENTS
GROUP SHARP CORPORATIO
SPECIFICATION
OlT’O-ELECI’RONIC
/
DEVICE SPECIFICATION FOR
VOLTAGE REGIJIX-OR
MODEL No.
PQ***EZO 12
Applied model name
D
1. These spectication sheets include materials protected under copyright of Sharp Corporation Wharp”).
Please do not reproduce or cause anyone to reproduce them without Sharp’s consent.
2. When using this product, please observe the absolute maximum ratings and the instructtons for use outlined
in these specitkation sheets, as well as the precautions mentioned below. Sharp assumesno responsibthty
for any damage resulting from use of the product which does not comply with the absolute mardmum ratings
and the instructions included in these speciflcatton sheets, and the precautions mentioned below.
(Precautions)
(1) This product is designed for use in the following application areas :
l OA equipment . Audio visual equipment
* TelecommuntcaUon equipment (Terminal)
[ l Tooling machines l Computers
1l Home appliances
l Measuring equipment
If the use of the product tn the above application areas is for equipment h&d in paragraphs
(2) or [3). please be sure to observe the precautions given in those respective paragraphs.
(2) Appropriate measures, such as fail-safe design and redundant design considering
the safety design of the overall system and equipment, should be taken to ensure reliability
and safety when this product is used for equipment whtch demands htgh relfabtltty and
safety in functfon and precision, such as :
l Transportation control and safety equipment (atrcraft, tram, automobile etc.)
l Traffic
signals
l Gas leakage sensor breakers l Rescueand securlly equipment
1[ l Other safety equipment
13) Pleasedo not use this product for equipment which require extremely high relfabthty
and safety in function and precision. such as :
.
* Space equipment l TelecommunicaUon equipment (for trunk lines>
1[ * Nuclear power control equipment * Medical equipment
i,
(4) Pleasecontact and consult with a Sharp sales representative if there are any questions
regarding interpretation of the above three paragraphs.
3. Please contact and consult with a Sharp sales representative for any questions about this product.
CUSTOMER’S APPROVAL
DATE
BY
DATE
PRESENTED
BY
K. Hachimura,
Department General Manager
Engineering Dept..11
Opto-Electronic Devices Div.
ELECOM Group
SHARP CORPORATION
of
SHRRP CORPORATION
3.2 EIectrlcal characteristics
Unless otherwise specified condition shall be Wn=Vo(TYP)+lV. Io=O.SmA. Vc=2.7V. Ta=25’c
Parameter
Symbol MIN. TYP. MAX. unit
Conditions
Input voltage
ViIl 2.35 -
10 v
Output voltage
vo
Refer to list 1
V
Load regulation
RegL - 0.2 2.0 % 10=5mA to 1A
Line regulation
vin=vo(TYP)+ 1v
RegI - 0.1 1.0. ow-v
to Vo(TYP)+6v
10=5mA
Temperature coefacient
of output voltage
TcVo
- fO.01 - %/C Io=SmA
Tj=O to 125C
Ripple rejection
RR 45 60 - dl3 Refer to Fig.3
Dropout voltage
vi-o - 0.2 0.5 v (‘5). 10=0.5A
On-state voltage for
control
Vc (on) 2.0
-
-
V
On-state current for
control
Ic (on) -
- 200 PA
Off-state voltage for
control
Vc (ofi) -
- 0.8 V
Off-state current for
control
Ic (off) - - 2 PA vc=o.4v
Quiescent current
Output off-state
consumption current
h - 1 2 mA Io=OA
Iqs
-
-
5 a PA
Io=OA
vc=o,4v
(*4) Applied to PQO30EZOlZ and PQO33EZOlZ.
(‘5) Input voltage when output voltage falls 0.95Vo by input voltage falling down,
(+6) In case that the control terminal (0 pin) is non-connection, output voltage should be
OFF state.
List 1 Output voltage
6 Page SHARP CORPORflTION
6.2 Packing specifications (PQ**+EZOlEP)
6.2.1 Packing conditions
(1) Tape structure and Dimensions (Refer to Fig. A)
The tape shall have a structure in whtch a cover tape is sealed heat-
pressed on the carrier tape of polystyrene emboss protect against
static electricity. Dimensions are shown Fig. A
(2) Reel structure and Dimensions (Refer to Fig.B)
The reel shall be made of polystyrene. Dimensions are shown Fig. B.
(3) Direction of product insertton (Refer to Fig. C)
Product direction in carrier tape shall direct to the radiate fin of product at
the hole side on the tape.
6.2.2 Tape characteristics
(1) Adhesiveness of cover tape
The peel-back force between carrier tape and cover tape shaU be
O.lN to 0.8N for the angle from 160’ to 180’ . (Tape speed : 5mm/s)
(2) Bending strength
Sealed tape : Bended tape radius shall be more than 30mm.
if bended tape radius is less than 3Omm.
there is case that cover tape come off carrier tape.
Carrier tape : Bended tape radius &all be more than 15mm.
6.2.3 Rolling method and quantity
(1) Rolling method
(. iI
Wind the tape back on the reel so that the cover tape will be outside the tape.
Attach more than 20 pitch of empty cavities to the trailer and attach more than
10 pitch of empty cavities to the leader of the tape and fix the both ends with
adhesive tape.
One reel shall‘contain 3000 PCS.
12 Page | ||
Seiten | Gesamt 19 Seiten | |
PDF Download | [ PQ030EZ01Z Schematic.PDF ] |
Teilenummer | Beschreibung | Hersteller |
PQ030EZ01Z | (PQ018EZ01Z / PQ025EZ01Z / PQ030EZ01Z / PQ033EZ01Z) DEVICE SPECIFICATION FOR VOLTAGE REGULATOR | Sharp Electrionic Components |
PQ030EZ01ZP | Low Voltage Operation Low Power-Loss Voltage Regulators | Sharp Electrionic |
PQ030EZ01ZPH | Compact Surface Mount type Low Power-Loss Voltage Regulators | Sharp Electrionic |
PQ030EZ01ZZ | Low Voltage Operation Low Power-Loss Voltage Regulators | Sharp Electrionic |
PQ030EZ01ZZH | Compact Surface Mount type Low Power-Loss Voltage Regulators | Sharp Electrionic |
Teilenummer | Beschreibung | Hersteller |
CD40175BC | Hex D-Type Flip-Flop / Quad D-Type Flip-Flop. |
Fairchild Semiconductor |
KTD1146 | EPITAXIAL PLANAR NPN TRANSISTOR. |
KEC |
www.Datenblatt-PDF.com | 2020 | Kontakt | Suche |