MAX810_EXR-T Datasheet PDF - Maxim Integrated
| Part Number | MAX810_EXR-T | |
| Description | 3-Pin Microprocessor Reset Circuits | |
| Manufacturers | Maxim Integrated | |
| Logo |  |
|
|
There is a preview and MAX810_EXR-T download ( pdf file ) link at the bottom of this page. Total 8 Pages | ||
Preview 1 page No Preview Available !
19-0344; Rev 4; 12/99
3-Pin Microprocessor Reset Circuits
General Description
The MAX803/MAX809/MAX810 are microprocessor (µP)
supervisory circuits used to monitor the power supplies
in µP and digital systems. They provide excellent circuit
reliability and low cost by eliminating external compo-
nents and adjustments when used with +5V, +3.3V,
+3.0V, or +2.5V-powered circuits.
These circuits perform a single function: they assert a
reset signal whenever the VCC supply voltage declines
below a preset threshold, keeping it asserted for at
least 140ms after VCC has risen above the reset thresh-
old. Reset thresholds suitable for operation with a vari-
ety of supply voltages are available.
The MAX803 has an open-drain output stage, while the
MAX809/MAX810 have push-pull outputs. The
MAX803’s open-drain RESET output requires a pull-up
resistor that can be connected to a voltage higher than
VCC. The MAX803/MAX809 have an active-low RESET
output, while the MAX810 has an active-high RESET
output. The reset comparator is designed to ignore fast
transients on VCC, and the outputs are guaranteed to
be in the correct logic state for VCC down to 1V.
Low supply current makes the MAX803/MAX809/
MAX810 ideal for use in portable equipment. The
MAX803 is available in a 3-pin SC70 package, and the
MAX809/MAX810 are available in 3-pin SC70 or SOT23
packages.
Applications
Computers
Controllers
Intelligent Instruments
Critical µP and µC Power Monitoring
Portable/Battery-Powered Equipment
Automotive
Typical Operating Circuit
VCC
VCC
MAX803
MAX809
RESET
RPULL-UP*
VCC
µP
RESET
INPUT
GND GND
*MAX803 ONLY
____________________________Features
o Precision Monitoring of +2.5V, +3V, +3.3V, and
+5V Power-Supply Voltages
o Fully Specified Over Temperature
o Available in Three Output Configurations
Open-Drain RESET Output (MAX803)
Push-Pull RESET Output (MAX809)
Push-Pull RESET Output (MAX810)
o 140ms min Power-On Reset Pulse Width
o 12µA Supply Current
o Guaranteed Reset Valid to VCC = +1V
o Power Supply Transient Immunity
o No External Components
o 3-Pin SC70 and SOT23 Packages
Ordering Information
PART
TEMP. RANGE PIN-PACKAGE
MAX803_EXR-T
-40°C to +105°C 3 SC70-3
MAX803_EXR-T10 -40°C to +105°C 3 SC70-3
MAX809_EXR-T
-40°C to +105°C 3 SC70-3
MAX809_EXR-T10 -40°C to +105°C 3 SC70-3
MAX809_EUR-T
-40°C to +105°C 3 SOT23-3
MAX809_EUR-T10 -40°C to +105°C 3 SOT23-3
MAX810_EXR-T
-40°C to +105°C 3 SC70-3
MAX810_EXR-T10 -40°C to +105°C 3 SC70-3
MAX810_EUR-T
-40°C to +105°C 3 SOT23-3
MAX810_EUR-T10 -40°C to +105°C 3 SOT23-3
Note: These parts are offered in 2.5k or 10k reels, and must be
ordered in 2.5k or 10k increments. Order MAX803_EXR-T for
2.5k reels and MAX803_EXR-T10 for 10k reels. Insert the
desired suffix letter from the Selector Guide into the blank to
complete the part number. All versions of these products may
not be available at the time of announcement. Contact factory for
availability.
Pin Configuration
TOP VIEW
GND 1
MAX803
MAX809
MAX810
3 VCC
RESET (RESET) 2
( ) ARE FOR MAX810.
SC70-3/SOT23-3
MAX803 AVAILABLE IN SC70-3 ONLY.
________________________________________________________________ Maxim Integrated Products 1
For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800.
For small orders, phone 1-800-835-8769.
|
| |
 
3-Pin Microprocessor Reset Circuits
_____________________Pin Description
PIN NAME
1 GND
RESET
(MAX803/
MAX809)
2
RESET
(MAX810)
3 VCC
FUNCTION
Ground
RESET Output remains low while VCC
is below the reset threshold, and for at
least 140ms after VCC rises above the
reset threshold.
RESET Output remains high while VCC
is below the reset threshold, and for at
least 140ms after VCC rises above the
reset threshold.
Supply Voltage (+5V, +3.3V, +3.0V, or
+2.5V)
VCC
MAX809
RESET
GND
R1
100k
Figure 2. RESET Valid to VCC = Ground Circuit
400
TA = +25°C
320
240
160
MAX8_ _J/L/M
80
MAX8_ _R/S/T/Z
0
1 10
100 1000
RESET COMPARATOR OVERDRIVE, VTH - VCC (mV)
Figure 1. Maximum Transient Duration Without Causing a
Reset Pulse vs. Reset Comparator Overdrive
Detailed Description
A microprocessor’s (µP’s) reset input starts the µP in a
known state. The MAX803/MAX809/MAX810 assert
reset to prevent code-execution errors during power-
up, power-down, or brownout conditions. They assert a
reset signal whenever the VCC supply voltage declines
below a preset threshold, keeping it asserted for at
least 140ms after VCC has risen above the reset thresh-
old. The MAX803 uses an open-drain output, and the
MAX809/MAX810 have a push-pull output stage.
Connect a pull-up resistor on the MAX803’s RESET out-
put to any supply between 0 and 6V.
Applications Information
Negative-Going VCC Transients
In addition to issuing a reset to the µP during power-up,
power-down, and brownout conditions, the MAX803/
MAX809/MAX810 are relatively immune to short-duration
negative-going VCC transients (glitches).
Figure 1 shows typical transient duration vs. reset com-
parator overdrive, for which the MAX803/MAX809/
MAX810 do not generate a reset pulse. The graph was
generated using a negative-going pulse applied to VCC,
starting 0.5V above the actual reset threshold and end-
ing below it by the magnitude indicated (reset compara-
tor overdrive). The graph indicates the maximum pulse
width a negative-going VCC transient can have without
causing a reset pulse. As the magnitude of the transient
increases (goes farther below the reset threshold), the
maximum allowable pulse width decreases. Typically, for
the MAX8__L and MAX8__M, a VCC transient that goes
100mV below the reset threshold and lasts 20µs or less
will not cause a reset pulse. A 0.1µF bypass capacitor
mounted as close as possible to the VCC pin provides
additional transient immunity.
Ensuring a Valid Reset Output
Down to VCC = 0
When VCC falls below 1V, the MAX809 RESET output
no longer sinks current—it becomes an open circuit.
Therefore, high-impedance CMOS logic inputs con-
nected to RESET can drift to undetermined voltages.
This presents no problem in most applications since
most µP and other circuitry is inoperative with VCC
below 1V. However, in applications where RESET must
be valid down to 0V, adding a pull-down resistor to
RESET causes any stray leakage currents to flow to
_______________________________________________________________________________________ 5
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for MAX810_EXR-T electronic component. |
| Information | Total 8 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ MAX810_EXR-T.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| MAX810_EXR-T | The function is 3-Pin Microprocessor Reset Circuits. Maxim Integrated | |
| MAX810_EXR-T10 | The function is 3-Pin Microprocessor Reset Circuits. Maxim Integrated | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
MAX8
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||