|
|
PDF LS7237 Data sheet ( Hoja de datos )
| Número de pieza | LS7237 | |
| Descripción | TOUCH CONTROL LAMP STEP DIMMER | |
| Fabricantes | LSI Computer Systems | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de LS7237 (archivo pdf) en la parte inferior de esta página. Total 4 Páginas | ||
|
No Preview Available !
LSI/CSI
LS7237
U
®
L
LSI Computer Systems, Inc. 1235 Walt Whitman Road, Melville, NY 11747 (631) 271-0400 FAX (631) 271-0405
A3800
TOUCH CONTROL LAMP STEP DIMMER
April 1995
FEATURES:
• PLL synchronization allows use as a Wall Switch
• Provides brightness control of an incandescent lamp
with a touch plate or mechanical switch
• Can control speed of shaded pole and universal AC motors
• Controls the "duty cycle" from 23% to 88% (conduction
angles for AC half-cycles between 45˚ and 158˚, respectively)
• Operates at 50Hz/60Hz line frequency
• Extension input for remote activation
• +12V to +18V DC Power Supply (VSS - VDD)
• 8-Pin Plastic DIP , 8-Pin SOIC-See Figure 1
PIN ASSIGNMENT - TOP VIEW
V SS (+V) 1
MODE 2
CAP 3
8 TRIG
7 V DD (-V)
6 EXT
DESCRIPTION:
LS7237 is a monolithic, MOS integrated circuit designed
to control the brightness of an incandescent lamp. The
output of the LS7237 triggers a triac connected in series
with a lamp(See Figure 5). The lamp brightness is de-
termined by controlling the output conduction angle (triac
triggering angle) in relation to the AC line frequency (See
Figure 2).
SYNC 4
FIGURE 1
INPUT/OUTPUT DESCRIPTION:
5
SENS
The output conduction angle can be varied by applying a
low level pulse at the SENS input or a high level pulse at
the EXT input. When implemented as shown in Figure 5,
this is accomplished by touching the Touch Plate which
causes the lamp brightness to change in specified steps
as follows:
VSS (Pin 1)
Supply voltage positive terminal.
MODE (Pin 2)
The operating mode for the circuit is selected by con-
necting this input as follows:
LEVEL
Off
Night Light
Mood Light
Medium
Maximum
BRIGHTNESS (% Rated Wattage)
0
9
29
66
99
The LS7237 can operate in one of three different modes
selected by the MODE input. The Brightness Sequences
produced by the different modes are as follows:
MODE
0
1
2
BRIGHTNESS SEQUENCE
Off-Max-Off
Off-Mood-Med-Max-Off
Off-Night-Mood-Med-Max-Off
After AC power-up, the output comes up in the OFF state.
Following that, every time the Touch Plate is touched, the
output steps to the next level of brightness. The next step
following the maximum brightness is the OFF state, in-
itiating a new sequence.
MODE INPUT
VSS
VDD
Float
SELECTED MODE
Mode 0
Mode 1
Mode 2
CAP (Pin 3)
PLL filter input capacitor. A 0.047µF capacitor should be
connected to this input.
SYNC (Pin 4)
The AC Line Frequency is applied to this input through an
external RC circuit (See Figure 5). The Phase-Lock Loop
in the IC synchronizes all internal timings to the AC signal
at the SYNC input.
SENS (Pin 5)
A low-level pulse applied to this input causes the TRIG out-
put to step to the next conduction angle in the sequence
selected by the MODE input. The change in conduction an-
gle takes place with the trailing edge of the SENS input
pulse.
7237-041100-1
1 page | ||
| Páginas | Total 4 Páginas | |
| PDF Descargar | [ Datasheet LS7237.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| LS7231 | TOUCH CONTROL LAMP DIMMER | LSI Computer Systems |
| LS7231-7234 | TOUCH CONTROL LAMP DIMMER | LSI Computer Systems |
| LS7232 | Touch indoor stepless dimming control IC |  ETC |
| LS7232ND | TOUCH CONTROL LAMP DIMMER | LSI Computer Systems |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |